REAR CRANKSHAFT OIL SEAL INSTALLATION

CAUTION / NOTICE / HINT

Note

When the manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release with bearing cylinder assembly to return to its original position, and dust from the moving section could damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.

PROCEDURE


  1. INSTALL REAR ENGINE OIL SEAL


    1. Using height adjustable attachments and plate lift attachments, place the engine assembly on a flat, level surface.

      Note


      • Using height adjustable attachments and plate lift attachments, place the engine assembly horizontally.

      • To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

      • Using an engine sling device and engine lift, secure the engine assembly before servicing.

    2. Remove any old seal packing.

      Note

      Be careful not to drop any oil on the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.

    3. A01M2ZHC05
      *a Seal Packing

      Apply seal packing in a continuous line as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note


      • Remove any oil from the contact surfaces.

      • Install a new rear engine oil seal within 3 minutes of applying seal packing.

      • Do not start the engine for at least 2 hours after installation.

    4. A01LVWEC13
      *a Seal Packing

      Wipe off the excess seal packing, leaving only the specified amount in the areas shown in the illustration.

    5. Using SST, press in a new rear engine oil seal until its surface is flush with the cylinder block sub-assembly and oil pan sub-assembly.

      A01M2ACC01
      *a Turn *b Hold
      *c Engine Front *d Engine Rear
      SST
      09223-47020   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021, 09955-05010, 09957-04010 )

      Tech Tips

      Rear engine oil seal tap in depth: -0.2 to 1.2 mm (-0.00787 to 0.0472 in.)

      Note


      • Make sure there is no foreign matter on the lip of the rear engine oil seal.

      • Make sure there is no oil or grease on the outer circumference of the rear engine oil seal.

      • Do not press in the rear engine oil seal at an angle.

      • Wipe off extra grease from the crankshaft.

      • Apply a small amount of molybdenum grease to the threaded portion and tip of SST center bolt (09953-05020) before using.

      Tech Tips

      If necessary, lightly tap SST using a plastic-faced hammer to insert the rear engine oil seal evenly.

      A01LXJ5N01
      SST
      09950-70010   ( 09951-07150 )
      09223-47020

  2. INSTALL FLYWHEEL SUB-ASSEMBLY


    1. A01M21IN01

      Using SST, hold the crankshaft.

      SST
      09960-10010   ( 09962-01000, 09963-01000 )

    2. Clean the 8 bolts and bolt holes.

    3. A01LV0KC37
      *a Adhesive

      Apply adhesive to 2 or 3 threads of each bolt end.

      Adhesive
      Toyota Genuine Adhesive 1324, Three bond 1324 or equivalent
    4. A01M22KN01

      Using several steps, uniformly install and uniformly tighten the 8 bolts in the order shown in the illustration.

      Torque:
      78 N*m  { 795 kgf*cm, 58 ft.*lbf }

      Note

      Do not start the engine for at least 1 hour after installation.

  3. INSTALL CLUTCH DISC ASSEMBLY

    Click here