SFI SYSTEM, Diagnostic DTC:P0365, P0367, P0368

DTC Code DTC Name
P0365 Camshaft Position Sensor "B" Circuit (Bank 1)
P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1)
P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1)

DESCRIPTION

The camshaft position sensor for the exhaust camshaft (EV1 signal) consists of a magnet and MRE (Magneto Resistive Element).

The exhaust camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0365 Camshaft Position Sensor "B" Circuit (Bank 1) No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or more (1 trip detection logic).

  • Open or short in camshaft position sensor (for exhaust camshaft) circuit

  • Camshaft position sensor (for exhaust camshaft)

  • Exhaust camshaft

  • Valve timing

  • ECM

 Comes on DTC stored
P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) The output voltage of the exhaust camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic).

  • Open or short in camshaft position sensor (for exhaust camshaft) circuit

  • Camshaft position sensor (for exhaust camshaft)

  • ECM

 Comes on DTC stored
P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) The output voltage of the exhaust camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).

  • Open or short in camshaft position sensor (for exhaust camshaft) circuit

  • Camshaft position sensor (for exhaust camshaft)

  • ECM

 Comes on DTC stored

Tech Tips

Reference: Inspection using an oscilloscope.

Click here

MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the exhaust camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Exhaust camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on.

  6. Start the engine.

  7. Idle the engine for 10 seconds or more.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  9. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  11. Input the DTC: P0365, P0367 or P0368.

  12. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

A01TCLUE07
*a Camshaft Position Sensor (for Exhaust Camshaft)

CAUTION / NOTICE / HINT

Tech Tips


  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  • If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))


    1. A01TCU2C27
      *a

      Front view of wire harness connector

      (to Camshaft Position Sensor (for Exhaust Camshaft))

      Disconnect the camshaft position sensor (for exhaust camshaft) connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B108-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)


    1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B108-1 (VVE+) - B31-80 (EV1+) Always Below 1 Ω
      B108-2 (VVE-) - B31-112 (EV1-) Always Below 1 Ω
      B108-1 (VVE+) or B31-80 (EV1+) - Body ground Always 10 kΩ or higher
      B108-2 (VVE-) or B31-112 (EV1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))


    1. Check the camshaft position sensor (for exhaust camshaft) installation condition.

      OK
      Camshaft position sensor is installed correctly.
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) Click here

    OK

  4. INSPECT EXHAUST CAMSHAFT


    1. Inspect the timing rotor of the exhaust camshaft.

      OK
      Camshaft timing rotor does not have any cracks or deformation.

      Tech Tips

      Perform "Inspection After Repair" after replacing the exhaust camshaft.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE EXHAUST CAMSHAFT Click here

    OK

  5. REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)


    1. Replace the camshaft position sensor (for exhaust camshaft).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Start the engine.

    7. Turn the GTS on.

    8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTC P0365, P0367 or P0368 is output A
      DTCs are not output B

    B

    END

    A

  7. ADJUST VALVE TIMING

    Result
    Proceed to
    NEXT

    Tech Tips

    There are no marks on the cylinder head to match up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to match up the alignment marks.

    Click here

    Result
    Proceed to
    NEXT

    NEXT

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Start the engine.

    7. Turn the GTS on.

    8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P0365, P0367 or P0368 is output B

      Tech Tips

      If the engine does not start, replace the ECM.


    A

    END

    B

    REPLACE ECM Click here

  9. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)


    1. Disconnect the camshaft position sensor (for exhaust camshaft) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B108-3 (VC2) - B31-111 (VCE1) Always Below 1 Ω
      B108-3 (VC2) or B31-111 (VCE1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR