ECD SYSTEM(w/o Glow Plug Controller), Diagnostic DTC:P0600, P0604, P0605, P0606, P0607, P060A, P060B, P060D, P0611, P061A, P061B, P061C, P062F

DTC Code DTC Name
P0600 Serial Communication Link
P0604 Random Access Memory (RAM)
P0605 Internal Control Module Read Only Memory (ROM) Error
P0606 ECM / PCM Processor
P0607 Control Module Performance
P060A Internal Control Module Monitoring Processor Performance
P060B Internal Control Module A/D Processing Performance
P060D Internal Control Module Accelerator Pedal Position Performance
P0611 Fuel Injector Control Module Performance
P061A Internal Control Module Torque Performance
P061B Internal Control Module Torque Calculation Performance
P061C Internal Control Module Engine RPM Performance
P062F Internal Control Module EEPROM Error

DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0600 Serial Communication Link

ECM internal error

(1 or 2 trip detection logic)

  • ECM

 Comes on DTC stored
P0604 Random Access Memory (RAM)

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P0605 Internal Control Module Read Only Memory (ROM) Error

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P0606 ECM / PCM Processor

ECM internal error

(1 or 2 trip detection logic)

  • ECM

 Comes on DTC stored
P0607 Control Module Performance

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P060A Internal Control Module Monitoring Processor Performance

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P060B Internal Control Module A/D Processing Performance

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P060D Internal Control Module Accelerator Pedal Position Performance

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P0611 Fuel Injector Control Module Performance

ECM internal error

(1 or 2 trip detection logic)

  • ECM

 Comes on DTC stored
P061A Internal Control Module Torque Performance

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P061B Internal Control Module Torque Calculation Performance

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P061C Internal Control Module Engine RPM Performance

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
P062F Internal Control Module EEPROM Error

ECM internal error

(1 trip detection logic)

  • ECM

 Comes on DTC stored
DTC Detection Drive Pattern
DTC No. DTC Detection Drive Pattern
P0600

One of following conditions is met:


  • Ignition switch ON

  • Engine idling

  • Vehicle being driven in a stop-and-go city drive pattern for more than 15 minutes.
P0604
P0605
P0606
P0607
P060A
P060B
P060D
P0611
P061A
P061B
P061C
P062F

CAUTION / NOTICE / HINT

Note

When replacing the ECM, perform ECM Initialization and Registration.

Click here

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  2. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 30 seconds or more.

    5. Turn the ignition switch to ON.

    6. Start the engine.

    7. Drive the vehicle with a stop-and-go city drive pattern for more than 15 minutes.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Confirm that the DTC is not output again.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    END