LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / (desired system) / Data List.

    5. According to the display on the intelligent tester, read the Data List.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Ignition switch ACC signal / ON or OFF

      ON: Ignition switch ACC

      OFF: Ignition switch off

      		 "ON" is also displayed for this item when the ignition switch is ON.
      IG SW Ignition switch ON signal / ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 "OFF" is also displayed for this item when the ignition switch is ACC.
      Parking Brake SW*1 Parking brake switch signal / ON or OFF

      ON: Parking brake switch on

      OFF: Parking brake switch off

      		 -
      Dimmer SW Dimmer switch high signal / ON or OFF

      ON: Dimmer switch in high or high flash

      OFF: Dimmer switch in low

      		 -
      Passing Light SW Dimmer switch high flash signal / ON or OFF

      ON: Dimmer switch in high flash

      OFF: Dimmer switch not in high flash

      		 -
      Rear Fog Light SW Rear fog light switch signal / ON or OFF

      ON: Rear fog light switch on

      OFF: Rear fog light switch off

      		 -
      Front Fog Light SW*2 Front fog light switch signal / ON or OFF

      ON: Front fog light switch on

      OFF: Front fog light switch off

      		 -
      Auto Light SW*3 Light control switch AUTO signal / ON or OFF

      ON: Light control switch in AUTO

      OFF: Light control switch not in AUTO

      		 -
      Head Light SW (Head) Light control switch head signal / ON or OFF

      ON: Light control switch in head

      OFF: Light control switch not in head

      		 -
      Head Light SW (Tail) Light control switch tail signal / ON or OFF

      ON: Light control switch in tail or head

      OFF: Light control switch not in tail or head

      		 -
      Illumination Rate Info Light control sensor illuminance / 0 to 65535 lx Value is output according to ambient light level -

      • *1: w/ Daytime Running Light

      • *2: w/ Front Fog Light

      • *3: w/ Automatic Light Control System

      HL Auto Leveling (for HID Headlight)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Headlight Low Beam State Low beam headlight state / ON or OFF

      ON: Low beam headlights on

      OFF: Low beam headlights off

      		 -
      +B Ignition power supply voltage value / 0 to 19.75 V 11 to 14 V -
      Height Sens Pw Supply Val Rear height control sensor power supply value / 0 to 5 V Approximately 5.0 V -
      Rr Height Sens Signal Val Rear height control sensor signal value / 0 to 5 V Approximately 2.5 V (When vehicle level) The value becomes larger when the front of the vehicle tilts up.
      Vehicle Speed Vehicle speed / 0 to 327.67 km/h A value similar to the actual vehicle speed is displayed -
      Rear Height Adjust Valid Flag Result of rear vehicle height calibration / VALID or INVALID

      VALID: Rear vehicle height calibration completed

      INVALID: Rear vehicle height calibration not completed

      		 -
      Init Writing Count Number of times initialization performed / 0 to 255 Current condition displayed -
      Sensor Initialization Hist Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied Current condition displayed -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / (desired system) / Active Test.

    5. According to the display on the intelligent tester, perform the Active Test.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Hazard Hazard signal ON / OFF -
      Daytime Running Light Daytime running light ON / OFF -
      Taillight Relay Taillight relay ON / OFF -
      Headlight Relay Low beam headlight relay ON / OFF -
      Head Light Hi Headlight dimmer relay ON / OFF -
      Front Fog Light Relay* Front fog light relay ON / OFF -
      Rear Fog Light Relay Rear fog light relay ON / OFF -

      • *: w/ Front Fog Light

      HL Auto Leveling
      Tester Display Test Part Control Range Diagnostic Note
      Drive The Leveling Motor UP Leveling motor ON / OFF -
      Drive The Leveling Motor DOWN Leveling motor ON / OFF -