FRONT WIPER MOTOR INSPECTION

PROCEDURE


  1. INSPECT FRONT WIPER MOTOR AND LINK ASSEMBLY (for LHD)


    1. Place matchmarks on the motor shaft and housing.

    2. A002QI2E41
      Text in Illustration
      *1

      Component without harness connected

      (Windshield Wiper Motor and Link Assembly (for LHD))

      Check the LO operation.


      1. Connect the positive (+) lead of the battery to terminal 1 (+1) and the negative (-) lead to terminal 5 (E), and check that the motor operates at low speed (LO).

        OK
        Motor operates at low speed (LO).
    3. A002QI2E04
      Text in Illustration
      *1

      Component without harness connected

      (Windshield Wiper Motor and Link Assembly (for LHD))

      Check the HI operation.


      1. Connect the positive (+) lead of the battery to terminal 4 (+2) and the negative (-) lead to terminal 5 (E), and check that the motor operates at high speed (HI).

        OK
        Motor operates at high speed (HI).
    4. A002QI2E42
      Text in Illustration
      *1

      Component without harness connected

      (Windshield Wiper Motor and Link Assembly (for LHD))

      Check the automatic stop operation.


      1. Connect the positive (+) lead of the battery to terminal 1 (+1) and the negative (-) lead to terminal 5 (E). With the motor operating at low speed (LO), disconnect terminal 1 (+1) to stop the wiper motor operation at any position other than the automatic stop position.

      2. Using SST, connect terminals 3 (+S) and 1 (+1). Then connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 5 (E) to restart the motor operation at low speed (LO).

        SST
        09843-18040

      3. Check that the motor stops automatically at the position where the matchmarks align.

        OK
        Motor stops automatically at the position where the matchmarks align.

        If the result is not as specified, replace the front motor and link assembly.

  2. INSPECT FRONT WIPER MOTOR AND LINK ASSEMBLY (for RHD)


    1. Place matchmarks on the motor shaft and housing.

    2. A002QI2E06
      Text in Illustration
      *1

      Component without harness connected

      (Windshield Wiper Motor and Link Assembly (for RHD))

      Check the LO operation.


      1. Connect the positive (+) lead of the battery to terminal 5 (+1) and the negative (-) lead to terminal 4 (E), and check that the motor operates at low speed (LO).

        OK
        Motor operates at low speed (LO).
    3. A002QI2E07
      Text in Illustration
      *1

      Component without harness connected

      (Windshield Wiper Motor and Link Assembly (for RHD))

      Check the HI operation.


      1. Connect the positive (+) lead of the battery to terminal 3 (+2) and the negative (-) lead to terminal 4 (E), and check that the motor operates at high speed (HI).

        OK
        Motor operates at high speed (HI).
    4. A002QI2E43
      Text in Illustration
      *1

      Component without harness connected

      (Windshield Wiper Motor and Link Assembly (for RHD))

      Check the automatic stop operation.


      1. Connect the positive (+) lead of the battery to terminal 5 (+1) and the negative (-) lead to terminal 4 (E). With the motor operating at low speed (LO), disconnect terminal 5 (+1) to stop the wiper motor operation at any position other than the automatic stop position.

      2. Using SST, connect terminals 1 (+S) and 5 (+1). Then connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 4 (E) to restart the motor operation at low speed (LO).

        SST
        09843-18040

      3. Check that the motor stops automatically at the position where the matchmarks align.

        OK
        Motor stops automatically at the position where the matchmarks align.

        If the result is not as specified, replace the front wiper motor and link assembly.