POWER WINDOW CONTROL SYSTEM Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

• If the auto up/down function does not operate, the cause may be one or more of the following:

• The ECU in the door window regulator determines that the door window regulator has not been initialized.

• The power window regulator switch has a malfunction.

• The Hall IC in the door window regulator has a malfunction.

• There is an open or short in the wiring between the power window regulator switch and the passenger side door window regulator.

WIRING DIAGRAM

PROCEDURE

1. CHECK FOR DTC

   
   

   1. Check for DTCs Click here.

      Result

      Result	Proceed to
      DTC is not output	A
      DTC B2311 is output	B
      DTC B2312 is output	C
      DTC B2313 is output	D
      LIN communication system DTCs are output	E

   
   

   B

   GO TO DTC B2311 Click here

   C

   GO TO DTC B2312 Click here

   D

   GO TO DTC B2313 Click here

   E

   GO TO LIN COMMUNICATION SYSTEM Click here

   A

2. CHECK MANUAL UP/DOWN FUNCTION (POWER WINDOW REGULATOR SWITCH)

   
   

   1. Check that the front passenger side door power window moves when the manual up/down function of the power window regulator switch is operated Click here.

      OK
      Front passenger side door power window moves.

   
   

   NG

   GO TO "Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch" Click here

   OK

3. READ VALUE USING INTELLIGENT TESTER (FRONT DOOR WINDOW REGULATOR ASSEMBLY RH)

   
   

   1. Use the Data List to check if the front door window regulator is functioning properly Click here.

      P-Door Motor

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      P Door P/W Auto SW	Front passenger side power window auto up/down signal / ON or OFF	ON: Front passenger side power window auto up/down switch operated OFF: Front passenger side power window switch not operated	-

      OK
      Display changes according to operation of power window regulator switch.

      Result	Proceed to
      OK (for LHD)	A
      OK (for RHD)	B
      NG	C

   
   

   A

   REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH Click here

   B

   REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH Click here

   C

4. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

   
   

   1. 

      Remove the power window regulator switch Click here.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition 8 (AUTO) - 1 (GND) Auto up/down operation Below 1 Ω 1 (GND) - Body ground Always Below 1 Ω

   
   

   NG

   REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

   OK

5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY)

   
   

   • *1: for LHD

   • *2: for RHD

   
   
   1. 

      Text in Illustration

      *1	for LHD
      *2	for RHD
      *3	Front view of wire harness connector (to Power Window Regulator Switch)
      *4	Front view of wire harness connector (to Front Door Window Regulator)

      Disconnect the J4*1 or K4*2 switch connector.

   2. Disconnect the J8*1 or K10*2 regulator connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD Tester Connection Condition Specified Condition J4-8 (AUTO) - J8-4 (AUTO) Always Below 1 Ω J4-8 (AUTO) or J8-4 (AUTO) - Body ground Always 10 kΩ or higher
      for RHD Tester Connection Condition Specified Condition K4-8 (AUTO) - K10-4 (AUTO) Always Below 1 Ω K4-8 (AUTO) or K10-4 (AUTO) - Body ground Always 10 kΩ or higher

      Result

      Result	Proceed to
      OK (for LHD)	A
      OK (for RHD)	B
      NG	C

   
   

   A

   REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY RH Click here

   B

   REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY LH Click here

   C

   REPAIR OR REPLACE HARNESS OR CONNECTOR