REAR DOOR REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. A002QQE

      Insert a clip remover between the plate and trim board.

    2. Turn the handle counterclockwise to remove the snap ring and handle.

  4. REMOVE REAR DOOR REGULATOR INSIDE HANDLE PLATE (w/o Power Window)


    1. Remove the inside handle plate.

  5. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    1. A002NPN

      Using moulding remover A, detach the 3 claws and remove the bezel.

  6. REMOVE REAR DOOR TRIM MOULDING LH


    1. A002M6I

      Using moulding remover A, detach the 8 claws and remove the rear door trim moulding.

  7. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)


    1. A002MH4

      Using moulding remover A, detach the 4 claws.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A002OM0

      Remove the 3 screws.

    2. Using a clip remover, detach the 10 clips.

    3. A002M42E02
      Text in Illustration
      *1 w/ Rear Door Sunshade
      *2 w/o Rear Door Sunshade

      Pull out the rear door trim board in the direction indicated by the arrow.

    4. A002LSW

      Disconnect the 2 cables from the inside handle.

    5. A002QVJ

      Detach the claw and remove the clamp.

  9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A002NCF

      Detach the 2 claws and remove the inside handle sub-assembly from the rear door trim board.

  10. REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. A002QEG

      Remove the 10 screws and curtain.

  11. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  12. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A002QC3

      Detach the 4 claws and remove the inner glass weatherstrip.

  13. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A002Q2V

      Disconnect the connector.

    2. A002OL5

      Remove the service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  14. REMOVE REAR DOOR GLASS RUN LH


    1. A002NAJ

      Remove the rear door glass run.

  15. REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)


    1. A002LO6

      Remove the 2 curtain hooks.

  16. REMOVE REAR DOOR FRAME GARNISH LH


    1. A002NZI

      Detach the clip and remove the rear door frame garnish.

  17. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. w/ Power Window:


      1. Temporarily install the regulator switch assembly.

      2. Connect the cable to the negative (-) battery terminal.

      3. Operate the regulator switch until the regulator reaches its bottom dead center.

      4. Disconnect the cable from the negative (-) battery terminal.

        Note

        When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

      5. Remove the regulator switch assembly.

    2. w/o Power Window:


      1. Temporarily install the rear door window regulator handle assembly.

      2. Turn the handle until the regulator reaches its bottom dead center.

      3. Remove the rear door window regulator handle assembly.

    3. A002QOC

      Remove the screw.

    4. Remove the 2 bolts and rear door window division bar sub-assembly.

  18. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A002OO4

      Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.

  19. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH


    1. A002P5P

      Remove the rear door quarter window weatherstrip from the rear door quarter window glass.

  20. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A002QI0

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  21. REMOVE REAR DOOR GLASS CHANNEL FILLER


    1. A002P9R

      Using a screwdriver, remove the glass channel.

      Note

      Be careful not to damage the glass.

    2. Remove the glass channel filler from the glass channel.

  22. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

  23. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. w/ Power Window:


      1. A002OGOE01
        Text in Illustration
        *1 Temporary Bolt

        Disconnect the connector.

      2. Loosen the temporary bolt.

        Note

        Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.

      3. Remove the 3 bolts.

      4. Remove the rear door window regulator assembly.

      5. Remove the temporary bolt from the rear door window regulator.

    2. A002PBV

      w/o Power Window:

      Remove the 3 bolts and regulator.

      Note

      Be careful when removing the bolts as the regulator may fall and become damaged.

  24. REMOVE REAR DOOR LOCK ASSEMBLY LH

    Click here

  25. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A002MAOE02
      *1 w/o Double Locking System:
      *2 w/ Double Locking System:

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A002QUNE02
      *1 w/o Double Locking System:
      *2 w/ Double Locking System:

      Remove the rear door remote control cable.

  26. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A002LULE02
      *1 w/o Double Locking System:
      *2 w/ Double Locking System:

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A002O1RE02
      *1 w/o Double Locking System:
      *2 w/ Double Locking System:

      Remove the rear door inside locking cable.

  27. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    1. A002LME

      Using a T30 ''TORX'' socket, loosen the screw and detach the claw to remove the outside handle cover.

  28. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A002MU6E04
      Text in Illustration
      *1 Holder

      Detach the holder as shown in the illustration.

    2. A002MVF

      Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

  29. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. A002LU5

      Detach the 3 claws and remove the pad.

  30. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. A002PM8

      Detach the 2 claws and remove the pad.

  31. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A002Q4C

      Using a T30 ''TORX'' socket, loosen the screw.

    2. Slide the outside handle frame to remove it.

      Tech Tips

      Remove the outside handle frame through the service hole.

  32. REMOVE REAR DOOR CHECK ASSEMBLY LH


    1. A002POU

      Remove the bolt, 2 nuts and door check.

      Tech Tips

      Remove the door check through the service hole.

      Note

      Be careful when removing the bolt and nuts as the door check may fall and become damaged.

  33. REMOVE REAR DOOR WEATHERSTRIP LH


    1. A002N2H

      Detach the 18 clips and remove the rear door weatherstrip.

  34. REMOVE NO. 3 BLACK OUT TAPE LH

    Click here

  35. REMOVE NO. 4 BLACK OUT TAPE LH

    Click here