LOWER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

Note


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND NUT

    Tech Tips

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

    A002OCUE05

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Remove the instrument panel safety pad sub-assembly Click here.

  5. REMOVE BOX PANEL SUB-ASSEMBLY


    1. Remove the box panel sub-assembly Click here.

  6. REMOVE STEERING PAD

    Click here

  7. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  8. REMOVE LOWER STEERING COLUMN COVER

    Click here

  9. REMOVE UPPER STEERING COLUMN COVER

    Click here

  10. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A002OCG

    1. Remove the 2 screws <A>.

    2. Detach the claw and guide, and remove the No. 1 instrument panel under cover.

  11. REMOVE FUSE BOX OPENING COVER

    A002P5E

    1. for LHD:


      1. Detach the 6 clips and 4 claws.

      2. Disconnect the connectors and remove the fuse box opening cover.

    2. for RHD:


      1. Detach the 5 clips and 4 claws.

      2. Disconnect the connectors and remove the fuse box opening cover.

        A002NVFE01
        *1 w/ Entry and Start System:
        *2 w/o Entry and Start System:

  12. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  13. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A002QU2

    1. Detach the 3 claws and guide, and remove the No. 2 instrument panel under cover.

  14. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

    A002PCT

    1. Push in the sides of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.

    2. Detach the glove compartment door stopper from the glove compartment door as shown in the illustration.

    3. A002LU0

      Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.

  15. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for Manual Air Conditioning System)

    Click here

  16. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

    Click here

  17. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    1. Detach the 3 claws and guide, and remove the front No. 1 console box insert.

      A002LJ1E01
      *1 for LHD:
      *2 for RHD:

  18. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. Detach the 3 claws and guide, and remove the front No. 2 console box insert.

      A002QYHE01
      *1 for LHD:
      *2 for RHD:

  19. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A002N1K

    1. Remove the screw <D>.

    2. Disconnect the connector.

    3. Detach the 4 clips and remove the lower No. 1 instrument panel finish panel.

  20. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. except Manual Transaxle:


      1. Remove the 4 nuts.

      2. Disconnect the connector, detach the clamp and move the shift lever assembly as shown in the illustration.

        A002Q37

    2. for Manual Transaxle:


      1. Remove the 4 nuts, and then move the shift lever assembly as shown in the illustration.

        A002NF4

    3. for LHD:


      1. Disconnect the connectors and clamps.

      2. Disconnect the hood lock control cable and DLC3.

        A002NDJE01
        Text in Illustration
        *1 Hood Lock Control Cable *2 DLC3

      3. Remove the 4 screws <D> and 2 bolts <B>.

      4. Remove the 11 bolts <C>.

      5. Detach the 6 guides and remove the lower instrument panel.

        A002OH3E03
        Text in Illustration
        *1 Bolt <B> *2 Bolt <C>
        *3 Screw <D> - -

    4. for RHD:


      1. Disconnect the connector and clamps.

      2. Disconnect the hood lock control cable and DLC3.

        A002PEEE02
        Text in Illustration
        *1 Hood Lock Control Cable *2 DLC3

      3. Remove the 4 screws <D> and 2 bolts <B>.

      4. Remove the 11 bolts <C>.

      5. Detach the 6 guides and remove the lower instrument panel.

        A002QCCE02
        Text in Illustration
        *1 Bolt <B> *2 Bolt <C>
        *3 Screw <D> - -

  21. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

    A002O3S

    1. Detach the claw and remove the glove compartment door stopper.

  22. REMOVE GLOVE COMPARTMENT DOOR LOCKCYLINDER ASSEMBLY (for RHD)

    A002OKSE01
    Text in Illustration
    *1 Protective Tape
    *2 Stopper

    1. Using a screwdriver, push the stopper of the glove compartment door lock cylinder as shown in the illustration and remove the glove compartment door lock cylinder in the direction of the arrow in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.