AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System), Diagnostic DTC:B1451/51

DTC Code DTC Name
B1451/51 Compressor Solenoid Circuit

DESCRIPTION

In this circuit, the compressor assembly with pulley receives a refrigerant compression demand signal from the air conditioning amplifier assembly. Based on this signal, the compressor assembly with pulley changes the degree of refrigerant compression.

DTC Code DTC Detection Condition Trouble Area
B1451/51 Open or short in the externally changeable compressor assembly with pulley solenoid circuit.

  • Compressor assembly with pulley

  • Harness or connector

  • Air conditioning amplifier assembly

WIRING DIAGRAM

A002MTTE02

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER


    1. Use the Data List to check if the compressor assembly with pulley is functioning properly.

      Air Conditioner
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Regulator Control Current Compressor assembly with pulley / Min.: 0, Max.: 0.997 Value changes between 0 A and 0.997 A in accordance with compressor assembly with pulley operation -
      OK
      The display is as specified in the normal condition column.
      Result
      Result Proceed to
      OK (When troubleshooting according to Problem Symptoms Table) A
      OK (When troubleshooting according to the DTC) B
      NG C

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    B

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    C

  2. INSPECT COMPRESSOR ASSEMBLY WITH PULLEY


    1. A002PVOE02

      except 1WW:

      Remove the compressor assembly with pulley Click here.

    2. for 1WW:

      Remove the compressor assembly with pulley Click here

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SOL+) - 1 (SOL-) 20°C (68°F) 10 to 11 Ω
      Result
      Result Proceed to
      OK A
      NG (except 1WW) B
      NG (for 1WW) C

    B

    REPLACE COMPRESSOR ASSEMBLY WITH PULLEY Click here

    C

    REPLACE COMPRESSOR ASSEMBLY WITH PULLEY Click here

    A

  3. CHECK HARNESS AND CONNECTOR (COMPRESSOR - BODY GROUND)


    1. except 1WW:


      1. A002MKCE02
        Text in Illustration
        *1

        Front view of wire harness connector

        (to Compressor Assembly with Pulley)

        Disconnect the C10 compressor connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        C10-1 (SOL-) - Body ground Always Below 1 Ω

    2. for 1WW:


      1. A002OM6E02
        Text in Illustration
        *1

        Front view of wire harness connector

        (to Compressor Assembly with Pulley)

        Disconnect the C91 compressor connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        C91-1 (SOL-) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (COMPRESSOR - AIR CONDITIONING AMPLIFIER)


    1. except 1WW:


      1. A002M96E01
        Text in Illustration
        *1

        Front view of wire harness connector

        (to Compressor Assembly with Pulley)
        *2

        Rear view of wire harness connector

        (to Air Conditioning Amplifier Assembly)

        Disconnect the C10 compressor connector.

      2. Disconnect the H46 amplifier connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        H46-2 (SOL+) - C10-2 (SOL+) Always Below 1 Ω
        H46-2 (SOL+) - Body ground Always 10 kΩ or higher

    2. for 1WW:


      1. A002N35E01
        Text in Illustration
        *1

        Front view of wire harness connector

        (to Compressor Assembly with Pulley)
        *2

        Rear view of wire harness connector

        (to Air Conditioning Amplifier Assembly)

        Disconnect the C91 compressor connector.

      2. Disconnect the H46 amplifier connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        H46-2 (SOL+) - C91-2 (SOL+) Always Below 1 Ω
        H46-2 (SOL+) - Body ground Always 10 kΩ or higher

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR