METER / GAUGE SYSTEM, Diagnostic DTC:B1500

DTC Code DTC Name
B1500 Fuel Sender Open Detected

DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction.

DTC Code DTC Detection Condition Trouble Area
B1500 The combination meter detects a fuel sender gauge assembly malfunction.

  • Harness or connector

  • Combination meter assembly

  • Fuel suction with pump assembly

  • Fuel sender gauge assembly

WIRING DIAGRAM

A002MAZE05

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (FUEL SENDER GAUGE)


    1. Use the Data List to check if the fuel receiver gauge is operating properly Click here.

      Combination Meter
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Fuel Input Fuel sender gauge input/Min.: 0, Max.: 127.5 Fuel sender gauge input value Unit: L
      OK
      Fuel amount value displayed on the intelligent tester is almost the same as needle indication.

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP ASSEMBLY AND BODY GROUND)


    1. Disconnect the H62 combination meter assembly connector.

    2. Disconnect the N18 fuel suction with pump assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H62-37 (L) - N18-2 (FS) Always Below 1 Ω
      H62-24 (E) - N18-3 (FE) Always Below 1 Ω
      H62-21 (ET) - Body ground Always Below 1 Ω
      H62-37 (L) or N18-2 (FS) - Body ground Always 10 kΩ or higher
      H62-24 (E) or N18-3 (FE) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT FUEL SUCTION WITH PUMP ASSEMBLY


    1. A002M8DE01
      Text in Illustration
      *1 Upper side
      *2 Lower side (to fuel sender gauge assembly)

      for 1ZR-FAE:

      Remove the fuel suction with pump assembly Click here.

    2. for 2ZR-FAE:

      Remove the fuel suction with pump assembly Click here.

    3. for 1WW:

      Remove the fuel suction with pump assembly Click here.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 (FS) - B-2 (FS) Always Below 1 Ω
      A-3 (FE) - B-1 (FE) Always Below 1 Ω
      Result
      Result Proceed to
      OK A
      NG (for 1ZR-FAE) B
      NG (for 2ZR-FAE) C
      NG (for 1WW) D

    B

    REPLACE FUEL SUCTION WITH PUMP ASSEMBLY Click here

    C

    REPLACE FUEL SUCTION WITH PUMP ASSEMBLY Click here

    D

    REPLACE FUEL SUCTION WITH PUMP ASSEMBLY Click here

    A

  4. INSPECT FUEL SENDER GAUGE ASSEMBLY


    1. for 1ZR-FAE:


      1. Remove the fuel sender gauge assembly Click here.

      2. Inspect the fuel sender gauge assembly Click here.

    2. for 2ZR-FAE:


      1. Remove the fuel sender gauge assembly Click here.

      2. Inspect the fuel sender gauge assembly Click here.

    3. for 1WW:


      1. Remove the fuel sender gauge assembly Click here.

      2. Inspect the fuel sender gauge assembly Click here.

      Result
      Result Proceed to
      OK A
      NG (for 1ZR-FAE) B
      NG (for 2ZR-FAE) C
      NG (for 1WW) D

    A

    REPLACE COMBINATION METER ASSEMBLY Click here

    B

    REPLACE FUEL SENDER GAUGE ASSEMBLY Click here

    C

    REPLACE FUEL SENDER GAUGE ASSEMBLY Click here

    D

    REPLACE FUEL SENDER GAUGE ASSEMBLY Click here