THEFT DETERRENT SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. According to the display on the intelligent tester, read the "Data List".

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Intrusion Sens OFF SW*1

      Intrusion sensor cancel switch /

      ON or OFF

      ON: Intrusion sensor cancel switch pushed

      OFF: Intrusion sensor cancel switch not pushed

      -
      Intrusion Sensor*1

      Intrusion sensor detection /

      ON or OFF

      ON: Moving object detected by sensor during arming preparation state or armed state

      OFF: No moving object detected by sensor

      -
      Hood Courtesy SW

      Engine hood courtesy switch /

      ON or OFF

      ON: Engine hood open

      OFF: Engine hood closed

      -
      Warning by Horn

      Security horn /

      ON or OFF

      ON: Security horn sounding

      OFF: Security horn not sounding

      -
      Intrusion Sen Conn*1

      Intrusion sensor setting /

      ON or OFF

      ON: Intrusion sensor set

      OFF: Intrusion sensor not set

      -
      Sealed Glas Brak Sen*2 Glass breakage sensor detection / With or Without

      With: Glass breakage sensor operates

      Without: Glass breakage sensor does not operate

      -
      D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF

      ON: Driver side door opened

      OFF: Driver side door closed

      -
      D-Door Lock Pos SW Driver side door lock position switch signal / ON or OFF

      ON: Driver side door unlocked

      OFF: Driver side door locked

      -
      Door Key SW-Lock Door key linked lock switch signal / ON or OFF

      ON: Driver side door key cylinder turned to lock position

      OFF: Driver side door key cylinder not turned

      -
      Door Key SW-Unlock Door key linked unlock switch signal / ON or OFF

      ON: Driver side door key cylinder turned to unlock position

      OFF: Driver side door key cylinder not turned

      -
      P Door Courtesy SW Front passenger side door courtesy light switch signal / ON or OFF

      ON: Front passenger side door opened

      OFF: Front passenger side door closed

      -
      P-Door Lock Pos SW Front passenger side door lock position switch signal / ON or OFF

      ON: Front passenger side door unlocked

      OFF: Front passenger side door locked

      -
      RL Door Courtesy SW Rear LH side door courtesy light switch signal / ON or OFF

      ON: Rear LH side door opened

      OFF: Rear LH side door closed

      -
      RL-Door Lock Pos SW Rear LH side door lock position switch signal / ON or OFF

      ON: Rear LH side door unlocked

      OFF: Rear LH side door locked

      -
      RR Door Courtesy SW Rear RH side door courtesy light switch signal / ON or OFF

      ON: Rear RH side door opened

      OFF: Rear RH side door closed

      -
      RR-Door Lock Pos SW Rear RH side door lock position switch signal / ON or OFF

      ON: Rear RH side door unlocked

      OFF: Rear RH side door locked

      -
      Back Door Courtesy SW Back door courtesy light switch signal / ON or OFF

      ON: Back door open

      OFF: Back door closed

      -
      Back Door Open Back door lock position status / Permit or Prohibit

      Permit: Back door unlocked

      Prohibit: Back door locked

      -
      IG SW Ignition switch status / ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      -
      ACC SW Ignition switch status / ON or OFF

      ON: Ignition switch ACC

      OFF: Ignition switch off

      -

      • *1: w/ Intrusion Sensor

      • *2: w/ Glass Breakage Sensor

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform the Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Active Test.

    5. According to the display on the intelligent tester, perform the "Active Test".

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Security Indicator Security indicator ON/OFF -
      Vehicle Horn Vehicle horn ON/OFF -
      Security Horn2 Theft warning siren (self power siren) ON/OFF -
      Power For Intrusion Sensor* Intrusion sensor power supply ON/OFF -

      *: w/ Intrusion Sensor