STEERING COLUMN ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A002M17E02
      Text in Illustration
      *1 Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

    2. A002P3J

      Install a new bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  2. INSTALL STEERING COLUMN PROTECTOR (for Manual Transaxle RHD)


    1. A002N8U

      Install the steering column protector to the steering column assembly with the bolt.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  3. INSTALL STEERING COLUMN ASSEMBLY


    1. A002LQ4E05
      Text in Illustration
      *1 Collar
      *2 Bushing

      Check that the 2 bushings are securely installed to the steering column assembly.

      Tech Tips

      If the bushings are missing or damaged, replace the steering column assembly with a new one.

    2. A002PRQ

      Install the steering column assembly with the bolt and 2 nuts.

      Torque:
      for bolt
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }
      for nut
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • Do not damage the 2 bushings.

      • Do not line-up the bolt hole by prying on the bushings. Only install the bolt straight, without applying any force to the bushings.

    3. A002M5W

      Connect the connector and attach the connector clamp.

    4. Install the bolt.

      Torque:
      8.4 N*m  { 85 kgf*cm, 74 in.*lbf }
    5. A002NUE

      Connect the power steering ECU connector.

  4. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. A002QN0E01
      Text in Illustration
      *1 Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

    2. A002QMQ

      Install a new bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  6. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY

    Click here

  7. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Install the lower No. 1 instrument panel airbag assembly Click here.

  8. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. Install the upper instrument panel sub-assembly Click here.

  9. INSTALL COLUMN HOLE COVER SILENCER SHEET


    1. A002MJP

      Install the column hole cover silencer sheet with the 2 clips.

    2. Install the floor carpet.

  10. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. A002NHHE02
      Text in Illustration
      *1 Clamp
      *2 Claw

      Using pliers, pinch the clamp and attach the claw to install the combination switch assembly with spiral cable sub-assembly to the steering column assembly.

    2. Connect the connectors to the combination switch assembly with spiral cable sub-assembly.

  11. INSTALL UPPER STEERING COLUMN COVER

    Note

    If the steering column cover is installed in an incorrect order, it will not be possible to assemble the steering column cover.


    1. A002OXG

      Attach the claw and 2 pins to install the upper steering column cover.

  12. INSTALL LOWER STEERING COLUMN COVER


    1. A002P1P

      Attach the 2 claws and install the steering column lower cover as shown in the illustration.

    2. A002NYF

      Attach the 4 claws.

    3. A002MAS

      Attach the claw.

      Tech Tips

      Press the area around the claw to attach it.

  13. ADJUST SPIRAL CABLE

    Click here

  14. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  15. INSTALL STEERING PAD

    Click here

  16. INSPECT STEERING WHEEL CENTER POINT

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  18. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.