ENGINE UNIT DISASSEMBLY

CAUTION / NOTICE / HINT

Note


  • After the engine has stopped, wait at least 1 minute before releasing the high pressure lines.

  • When working on the fuel circuit, protect the generator assembly against dirt contamination. Cover generator assembly with suitable materials. Failure to comply with this procedure may result in a generator assembly malfunction.

  • A002MXWE01

    After disconnecting the pressure line, it is absolutely essential to seal the injector assemblies and the common rail assembly with SST.

    SST
    PZ4TB-04941-79

PROCEDURE


  1. REMOVE CAMSHAFT POSITION SENSOR

    Click here

  2. REMOVE CRANKSHAFT POSITION SENSOR

    Click here

  3. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

    Click here

  4. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

    Click here

  5. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

    Click here

  6. REMOVE INJECTOR ASSEMBLY

    Click here

  7. REMOVE ENGINE WATER PUMP ASSEMBLY

    Click here

  8. REMOVE WATER BY-PASS PIPE


    1. A002NG7

      Using a 5 mm hexagon socket wrench, remove the bolt and water by-pass pipe from the water inlet housing.

  9. REMOVE WATER INLET

    Click here

  10. REMOVE THERMOSTAT

    Click here

  11. REMOVE WATER INLET HOUSING


    1. A002QAO

      Using an E11 "TORX" socket wrench, remove the 5 bolts and water inlet housing.

  12. REMOVE WATER OUTLET


    1. A002ONQ

      Using an E10 "TORX" socket wrench, remove the 3 bolts and water outlet.

    2. Remove the gasket from the water outlet.

  13. REMOVE OIL FILTER SUB-ASSEMBLY

    Click here

  14. REMOVE OIL FILTER ASSEMBLY

    Click here

  15. SET NO. 1 CYLINDER TO TDC/COMPRESSION

    Click here

  16. REMOVE OIL FILLER CAP SUB-ASSEMBLY

  17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

  18. HOLDING CAMSHAFT AND NO. 2 CAMSHAFT

    Click here

  19. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

    Click here

  20. REMOVE NO. 2 TIMING CHAIN GUIDE

    Click here

  21. REMOVE CAMSHAFT AND NO. 2 CAMSHAFT

    Click here

  22. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

    Click here

  23. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

    Click here

  24. REMOVE VALVE LASH ADJUSTER ASSEMBLY

    Click here

  25. REMOVE CYLINDER HEAD SUB-ASSEMBLY

    Click here

  26. REMOVE CYLINDER HEAD GASKET


    1. Remove the cylinder head gasket from the cylinder block.

  27. REMOVE CRANKSHAFT PULLEY

    Click here

  28. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL

    Click here

  29. REMOVE CLUTCH COVER ASSEMBLY

    Click here

  30. REMOVE CLUTCH DISC ASSEMBLY

    Click here

  31. REMOVE FLYWHEEL WITH DAMPER ASSEMBLY

    Click here

  32. REMOVE FUEL SUPPLY PUMP ASSEMBLY


    1. A002QPD

      Remove the sealing cap from the timing chain cover plate.

    2. Remove the O-ring from the sealing cap.

    3. A002LJBE01

      Using SST B, install SST A to position the fuel supply pump assembly. Then remove SST B.

      SST
      PZ4TB-04967-25

      Note

      SST A remains in the timing chain cover plate until the end of the repair work.

    4. A002NQQ

      Remove the 4 bolts and fuel supply pump assembly support.

    5. A002O0Q

      Remove the 2 bolts from the fuel supply pump assembly.

    6. A002N8RE01
      Text in Illustration
      *1 Central Bolt

      Remove the screw connection between the fuel supply pump assembly and injection pump drive gear.

      Note


      • SST A remains in the timing chain cover plate.

      • The central bolt is supported on SST A until the fuel supply pump assembly pressed out.

      • A002LHCE03

        The central bolt remains inside SST A attached to the injection pump drive gear.

    7. Remove the fuel supply pump assembly from the cylinder block.

  33. REMOVE OIL PAN SUB-ASSEMBLY

    Click here

  34. REMOVE OIL STRAINER SUB-ASSEMBLY

    Click here

  35. REMOVE OIL PUMP WITH VACUUM PUMP ASSEMBLY

    Click here

  36. REMOVE REAR ENGINE OIL SEAL

    Click here

  37. REMOVE TIMING CHAIN COVER PLATE


    1. A002PWW

      Using an E8 "TORX" socket wrench, remove the 11 bolts and timing chain cover plate.

  38. REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY


    1. A002NSD

      Remove the oil pump drive chain sub-assembly from the crankshaft.

  39. REMOVE NO. 2 CHAIN SUB-ASSEMBLY


    1. A002LIL

      Remove the No. 2 chain sub-assembly from the injection pump drive gear.

  40. REMOVE NO. 2 TIMING CHAIN TENSION ARM


    1. A002Q5L

      Using a T45 "TORX" socket wrench, remove the bolt and No. 2 timing chain tension arm.

  41. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    1. A002MTHE02
      Text in Illustration
      *a Hexagon Wrench

      Slowly push the plunger deep into the No. 1 chain tensioner assembly and insert a 3.0 mm hexagon wrench into the No. 1 chain tensioner assembly.

    2. A002M3I

      Using an E8 "TORX" socket wrench, remove the 2 bolts and No. 1 chain tensioner assembly.

  42. REMOVE TIMING CHAIN TENSION ARM


    1. A002N48

      Using a T45 "TORX" socket wrench, remove the bolt and timing chain tension arm.

  43. REMOVE TIMING CHAIN GUIDE


    1. A002M00

      Using a T45 "TORX" socket wrench, remove the 2 bolts and timing chain guide.

  44. REMOVE INJECTION PUMP DRIVE GEAR


    1. A002Q4S

      Remove the injection pump drive gear and chain sub-assembly.

  45. REMOVE NO. 2 OIL NOZZLE SUB-ASSEMBLY


    1. A002QU1

      Using an E8 "TORX" socket wrench, remove the bolt and No. 2 oil nozzle sub-assembly.