DIFFERENTIAL CASE REASSEMBLY

PROCEDURE


  1. INSTALL FRONT DIFFERENTIAL SIDE GEAR


    1. A002NFWE01
      Text in Illustration
      *1 Front Differential Side Gear
      *2 Conical Spring
      *3 front differential side gear thrust washer
      A002OPC Gear Oil

      Apply gear oil to the front differential side gear, front differential side gear thrust washer and conical spring

    2. A002OUYE02
      Text in Illustration
      *1 Front Differential Side Gear
      *2 Conical Spring
      *3 front differential side gear thrust washer

      Install the 2 front differential side gears, 2 front differential side gear thrust washers and 2 conical springs to the front No. 1 differential case sub-assembly.

      Note


      • Do not drop the front differential side gear, front differential side gear thrust washer and conical spring.

      • Make sure that the conical spring is installed in the correct direction.

    3. Set SST as shown in the illustration and tighten it.

      SST
      09528-52010   ( 09953-05010, 09528-05010 )
      A002O97E02
      Text in Illustration
      *a Turn *b Hold

      Tech Tips


      • Tighten SST until the front differential pinion can enter the front No. 1 differential case sub-assembly.

      • When installing the front differential pinion, do not overtighten SST, as it is necessary to rotate the front differential side gear.

    4. A002MGQ

      Apply gear oil to the front differential pinion thrust washer.

      Text in Illustration
      A002OPC Gear Oil
    5. A002PCN

      Apply gear oil to the front differential pinion.

      Text in Illustration
      A002OPC Gear Oil
    6. A002MLQE01
      Text in Illustration
      *a Turn

      Using SST as shown in the illustration, rotate the front differential side gear and install the 2 front differential pinions and 2 front differential pinion thrust washers.

      SST
      09528-52010   ( 09528-05030 )

      CAUTION:

      Be careful not to catch your fingers between the front differential pinion and front No. 1 differential case sub-assembly.

      Note

      Do not drop the front differential pinion and front differential pinion thrust washer.

  2. INSPECT FRONT DIFFERENTIAL PINIONBACKLASH

    Click here

  3. INSTALL FRONT NO. 1 DIFFERENTIAL PINIONSHAFT


    1. A002N8H

      Apply gear oil to the front No. 1 differential pinion shaft.

      Text in Illustration
      A002OPC Gear Oil

    2. Install the front No. 1 differential pinion shaft to the front No. 1 differential case sub-assembly so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front No. 1 differential case sub-assembly.

  4. INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY

    Click here

  5. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN


    1. A002OTS

      Using a 5 mm pin punch and hammer, tap in the front differential pinion shaft straight pin to the front No. 1 differential case sub-assembly.

    2. A002Q6B

      Using a chisel and hammer, stake the front No. 1 differential case sub-assembly.

  6. INSTALL FRONT DIFFERENTIAL RING GEAR


    1. Clean the contact surfaces of the front No. 1 differential case sub-assembly and front differential ring gear.

    2. Using a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F) in boiling water.

    3. A002NWLE02
      Text in Illustration
      *a Matchmark

      After the moisture on the front differential ring gear has completely evaporated, quickly align the matchmarks on the front differential ring gear and the front No. 1 differential case sub-assembly and install the front differential ring gear to the front No. 1 differential case sub-assembly.

    4. Install the 16 bolts.

      Torque:
      106 N*m  { 1081 kgf*cm, 78 ft.*lbf }

  7. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    1. A002PRNE01

      Using SST and a press, press in a new front differential case front tapered roller bearing.

      SST
      09523-36010
      09950-60010   ( 09951-00460, 09951-00560, 09952-06010 )
      09950-70010   ( 09951-07150 )

  8. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    1. A002LOSE01

      Using SST and a press, press in a new front differential case rear tapered roller bearing.

      SST
      09554-22010