DESCRIPTION
The engine stop and start ECU records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Note
Freeze frame data values will vary depending on the measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.
Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data using the GTS.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check for DTCs and read the freeze frame data.
LIST OF FREEZE FRAME DATA
| Tester Display | Measurement Item |
|---|---|
| Coolant Temp | Engine coolant temperature |
| Engine Spd (ECM) | Engine speed signal from ECM through CAN communication |
| Engine Spd (NE Signal) | Engine speed signal from ECM via direct line |
| Deceleration Sens Offset Val | Deceleration sensor offset value |
| Deceleration Sens Calibration | Deceleration sensor calibration status |
| Gradient of Road Surface | Degree of road gradient |
| Battery Voltage | Battery voltage |
| Battery Voltage 2 | VB- voltage |
| Battery Fluid Temperature | Battery fluid temperature |
| Battery Temp (Start) | Battery temperature at engine start |
| Engine Type Information | Information on the engine type from the ECD system |
| Starter Type | Starter assembly type |
| D Courtesy Switch Signal | Driver door courtesy switch signal |
| Hood Courtesy Switch | Hood courtesy switch signal |
| Neutral Switch | Neutral start switch assembly signal |
| Clutch Upper SW | Clutch switch assembly (for upper) signal |
| Clutch Lower SW | Clutch start switch assembly (for lower) signal |
| Starter | Starter status |
| Pinion Gear | Unused |
| Starter Motor | Unused |
| TC Terminal | TC and CG terminals of DLC3 |
| Cancel Switch | Stop and start system cancel switch (ecorun cancel switch assembly) signal |
| IG Switch | Ignition or starter switch assembly*1 or push start switch*2 signal |
| Idle | Engine idling status |
| Engine Start (IG SW) | Engine start by ignition or starter switch assembly*1 or push start switch*2 operation |
| Stop Light SW (ECM) | Stop light switch assembly signal from ECM |
| Stop Light SW (ABS/VSC) | Stop light switch assembly signal from brake system |
| Fuel Heater Signal(ECD) | Combustion type power heater signal |
| Engine Starter Signal | Starter signal status |
| Buzzer | Buzzer status |
| Indicat. Light Eco | Stop and start indicator light status |
| Oil Prs Warn Light Prohibit | Unused |
| S&S Cancel Light Code | Transmission code from the engine stop and start ECU to the combination meter assembly |
| Starter Operation # | Number of starter operations (count record) |
| Number of Engine Starts (IG-ON) | The number of starter operations by ignition or starter switch assembly*1 or push start switch*2 operation |
| Number of Engine Starts (Stop & Start) | The number of starter operations by stop and start control |
| Number of Engine Starts (Clutch Released) | The number of starter operations without clutch pedal being depressed |
| Number of Engine Starts (Clutch Half-Depressed) | The number of starter operations with clutch pedal depressed halfway |
| Vehicle Spd1 (ABS/VSC) | Vehicle speed signal from skid control ECU (brake actuator assembly) through CAN communication |
| Steering Angle | Steering wheel steering angle amount |
| Steering Wheel Torque | Steering wheel torque amount |
| Battery Current | Battery current |
| Brake Boost Pressure | Brake booster pressure (absolute pressure) |
| Brake Negative Pressure | Brake booster vacuum (negative pressure) |
| Ambient Temp Sensor | Ambient temperature |
| Stop&Start of Eng State | Stop and start control status |
| Idling Stop Rate | Rate of the idling stop time to the entire ignition switch ON time |
| Total Idling Stop Rate | Rate of the idling stop time to the entire ignition switch ON time |
| Integrated Current | Battery integrated current |
| Cranking Time | Engine cranking time (in current trip) (When minimum voltage is detected at engine start) |
| Min Voltage(Cranking) | Minimum battery voltage while engine cranking (in current trip) |
| Min Volt(After Cranking) | Minimum battery voltage just after engine cranking |
| Status of Battery Charge Control | Battery charge control status |
| State of BBC | Backup boost converter status |
| BBC Check Result | Backup boost converter check result |
| Atmosphere Pressure | Atmospheric pressure (calculated value) |
| EPS Load | Electric power steering current |
| Accelerator Position | Accelerator pedal position |
| Engine OFF Request | Engine stop request |
| Manual Start during S&S | Manual start during stop and start control operation |
| Wrong Operation (Start) | Wrong operation for engine start |
| Engine Reverse Rev. | Engine reverse revolution status |
| N/Clutch Lower SW Abnoml | Clutch start switch assembly (for lower) |
| N/Clutch Upper SW Abnoml | Clutch switch assembly (for upper) |
| Permit Idling Stop | Engine stop standby |
| Running History | Vehicle driving record |
| Steering Angle Sensor Malfunction | Whether a steering angle sensor malfunction exists |
| Steering Angle Sensor Circuit Open (+B) | Whether there is an open to +B in the steering angle sensor circuit |
| Steering Angle Sensor Abnormal Value | Whether there is an abnormality in the value continuously input from the steering angle sensor |
| Steering Torque Sensor Malfunction | Whether a steering torque sensor malfunction exists |
| EPS Current Enable on Assist | Whether the power steering assist current value is available |
| Auto A/C | Availability of air conditioning system on vehicle |
| Eng Start Req (A/C 2) | Engine start request from the air conditioning system |
| Wheel Speed Malfunction | Wheel speed malfunction status |
| E/G ECU Region Mismatch | ECM region mismatch status |
| Oper Permission (Neutral Switch) | Permission of stop and start control based on the neutral position sensor (neutral position switch) conditions |
| Oper Permission (Idling) | Unused |
| Oper Permission (Vehicle Speed) | Permission of stop and start control based on the vehicle speed conditions |
| Stop&Start Precondition | Permission of stop and start control with all preconditions met. Condition of permission or prohibition for terms listed below. (ECM1, ECM2, idling, battery, ABS/VSC2, IGSW, DTC, A/C, interval, after running, engine hood closed, D door closed, cancel switch, steering, interval for starter, key operation, driver side buckle SW, ambient temperature) |
| Stop&Start Precondition 2 | Permission of stop and start control with all preconditions met. Condition of permission or prohibition for terms listed below. (Brake negative pressure, starter check complete) |
| Oper Permission (ECM 1) | Permission of stop and start control by the ECM |
| Oper Permission (ECM 2) | Permission of stop and start control by ECD system |
| Oper Permission (IG SW) | Permission of stop and start control based on the ignition or starter switch assembly*1 or push start switch*2 conditions |
| Oper Permission (DTC) | Permission of stop and start control based on the DTC output conditions |
| Oper Permission (Brake Negative Pressure) | Permission of stop and start control based on the brake booster vacuum conditions |
| Oper Permission (Interval) | Permission of stop and start control based on the engine running time conditions |
| Oper Permission (D Door Closed) | Permission of stop and start control based on the driver door open/close conditions |
| Oper Permission (Engine Hood Closed) | Permission of stop and start control based on the engine hood open/close conditions |
| Oper Permission (A/C) | Permission of stop and start control based on the air conditioning conditions |
| Oper Permission (Ambient Temperature) | Permission of stop and start control based on the ambient temperature conditions |
| Oper Permission (After Running) | Permission of stop and start control based on the initial trip conditions after the ignition switch is turned to ON |
| Oper Permission (Neutral SW OFF History) | Permission of stop and start control based on the shift operation history |
| Oper Permission (Clutch Upper SW OFF History) | Permission of stop and start control based on the clutch pedal operation history |
| Oper Permission (Battery) | Permission of stop and start control based on the battery conditions |
| Oper Permission (Start Min Volt 1) | Permission of stop and start control based on the battery conditions
|
| Oper Permission (Start Min Volt 2) | Permission of stop and start control based on the battery conditions
|
| Oper Permission (Start Min Volt 3) | Permission of stop and start control based on the battery conditions
|
| Oper Permission (Start Min Volt 4) | Permission of stop and start control based on the battery conditions
|
| Oper Permission (Battery Current) | Permission of stop and start control based on the battery conditions |
| Oper Permission (Integrated Current) | Permission of stop and start control based on the integrated current value conditions |
| Oper Prohibition (Jump Start) | Prohibition of stop and start control based on the jump start conditions |
| Oper Prohibition (Manual Start) | Prohibition of stop and start control based on the manual start conditions |
| Oper Permission (Interval For Starter) | Permission of stop and start control based on the conditions after engine restart |
| Oper Permission (Cancel Switch) | Permission of stop and start control based on the stop and start system cancel switch (ecorun cancel switch assembly) operation |
| Oper Permission (ABS/VSC 2) | Permission of stop and start control by the vehicle stability control system |
| Oper Permission (Road Surface Gradient) | Permission of stop and start control based on the road grade conditions |
| Oper Permission (Driver Side Buckle SW) | Permission of stop and start control based on the driver seat belt condition |
| Oper Permission (Steering) | Permission of stop and start control by the power steering ECU assembly |
| Oper Permission (Key Operation) | Permission of stop and start control based on the ignition or starter switch assembly*1 or push start switch*2 operation |
| Oper Permission (Starter Check Complete) | Permission of stop and start control based on the starter circuit self-check result |
| Oper Prohibition (Engine F/C) | Prohibition of stop and start control based on the engine fuel-cut prohibition signal |
| Eng Start Req (Brk Negative Pressure Low) | Engine start request due to low brake booster vacuum |
| Eng Start Req (IG Switch) | Engine start request due to ignition or starter switch assembly*1 or push start switch*2 operation |
| Eng Start Req (ECM) | Engine start request from ECM |
| Eng Start Req (A/C) | Engine start request from air conditioning system |
| Eng Start Req (Steering) | Engine start request by the power steering system |
| Eng Start Req (Detect DTC) | Engine start request due to output of DTCs |
| Eng Start Req (Clutch Pedal) | Engine start request due to clutch pedal operation |
| Eng Start Req (Clutch Lower SW) | Engine start request by the clutch start switch assembly (for lower) |
| Eng Start Req (Engine Hood Open) | Engine start request due to opening of engine hood |
| Eng Start Req (Battery Condition) | Engine start request based on battery performance |
| Eng Start Req (CVT Vehicle Speed) | Unused |
| Eng Start Req (ABS Vehicle Speed) | Engine start request based on vehicle speed signal from the brake system |
| Eng Start Req(Cancel SW) | Engine start request by stop and start system cancel switch (ecorun cancel switch assembly) |
| Eng Start Req(Courtesy SW or Buckle SW) | Engine start request by courtesy switch (driver side) or driver side buckle switch |
| ABS Running | Unused |
| Clutch SW Signal Abnoml | Malfunction in the clutch start switch assembly |
| Crank Pos Sen Abnoml 3 | Fail-safe operation due to abnormal engine speed signal |
| N Position Switch | Neutral position sensor (neutral position switch) status |
| Brk Boost Sen Abnoml 1 | Malfunction in the vacuum sensor assembly (ON is displayed when the input value from the vacuum sensor assembly is 4.5 V or more, or 0.5 V or less) |
| Brk Boost Sen Abnoml 2 | Malfunction in the vacuum sensor assembly (ON is displayed when STP changes from ON to OFF due to sticking of the vacuum sensor assembly causing fluctuation in the sensor value to be small) |
| Brk Boost Sen Abnoml 3 | Malfunction in the vacuum sensor assembly (ON is displayed when a change in the sensor value is small, even though the vehicle speed has increased from 0 km/h (0 mph) to 30 km/h (18.6 mph) 30 times, due to sticking of the vacuum sensor assembly) |
| Starter Count Abnoml | Error in the number of starter operations |
| Starter Circuit Abnoml | Malfunction in the starter circuit |
| Starter Circuit Open | Open in the starter circuit (STA malfunction) |
| Alternator Status | Alternator power generation status |
| BBC Abnoml | Malfunction in the backup boost converter |
| BBC Overcurrent | Overcurrent in boosting output from the backup boost converter |
| BBC Duty | Abnormal duty of the backup boost converter |
| BBC Power Low | Decrease in backup boost converter output |
| BBC Over Heat | Overheating of the backup boost converter |
| BBC Thermistor | Malfunction in the backup boost converter thermistor |
| IG SW Abnoml | Malfunction in the ignition or starter switch assembly*1 or push start switch*2 |
| Battery Abnoml | Malfunction in the power source |
| Sensor Supply Voltage Low Status | Drop in the sensor power source voltage |
| Comm Err with ECM | Communication error with the ECM |
| Comm Err with ABS/VSC | Communication error with the skid control ECU (brake actuator assembly) |
| Comm Err with EPS | Communication error with the power steering ECU assembly |
| Comm Err with J/B | Communication error with the main body ECU (multiplex network body ECU) |
| Comm Err with A/C | Communication error with the air conditioning amplifier assembly |
| Comm Err with Air Bag | Communication error with the center airbag sensor assembly |
| Comm Err with Meter | Communication error with the combination meter assembly |
| Comm Err with G Sensor | Communication error with the deceleration sensor (yaw rate sensor) |
| Comm Err with Steering Angle Sensor | Communication error with the steering angle sensor (spiral with sensor cable sub-assembly) |
| CPU Duty | Error in CPU duty |
| EEPROM | Error in EEPROM |
| Dec Sensor Calibration | Deceleration sensor zero point uncalibrated |
| Deceleration Sensor Movement | Sticking of the deceleration sensor |
| Engine Stall | Engine stall history |
| Engine Stall History during S&S(Hood Open) | History of engine stall caused by depressing the clutch pedal with the engine hood open while the engine is stopped by stop and start control (shift lever in neutral) |
| Engine Stall History during S&S(Collision or Battery Voltage Low) | History of engine stall due to a collision or low battery voltage when the stop and start control is operating |
| Engine Stall History during Engine Starting (Collision) | History of engine stall due to a collision while the engine is stopped by stop and start control |
| Engine Start Fail | History of engine restart failure by stop and start control |
| Voltage Judgment | Error in voltage judgment |
| VB Voltage Low | Open in VB- circuit |
| AD Converter Malfunction | Malfunction in the Analog to Digital converter |
| Starter Relay Overcurrent | Overcurrent in the starter relay |
| NE Sensor Circuit Open2 | Malfunction in the crankshaft position sensor circuit |
| Brk Boost Malfunc 1 | Fail-safe operation due to malfunction in the vacuum sensor assembly. Fail-safe operation due to sticking of the vacuum sensor assembly (a change in the sensor value is small when STP signal changes from ON to OFF) |
| Brk Boost Malfunc 2 | Fail-safe operation due to malfunction in the vacuum sensor assembly. Fail-safe operation due to sticking of the vacuum sensor assembly (a change in the sensor value is small, even though the vehicle speed has increased from 0 km/h (0 mph) to 30 km/h (18.6 mph) 30 times) |
| N Position Voltage Status | Malfunction in the neutral position sensor (neutral position switch) |
| Num of Current Code | Number of currently stored DTCs |
*1: w/o Entry and Start System
*2: w/ Entry and Start System