STOP AND START SYSTEM Stop and Start System does not Operate (Battery Condition)

DESCRIPTION

When the stop and start system does not operate, check whether the operation is prohibited because the battery conditions are not met.

Tech Tips

Data List items:


  • Oper Permission (Battery)

  • Oper Permission (Start Min Volt 1)

  • Oper Permission (Start Min Volt 2)

  • Oper Permission (Start Min Volt 3)

  • Oper Permission (Start Min Volt 4)

  • Oper Permission (Battery Current)

  • Oper Permission (Integrated Current)

  • Oper Prohibition (Jump Start)

  • Oper Prohibition (Manual Start)

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  2. READ VALUE USING GTS


    1. Enter the following menus: Powertrain / Stop and Start / Data List.

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Battery)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Stop and start control is permitted due to battery condition, or Active Test (forced permission) is performed -
      Oper Permission (Start Min Volt 1)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or less and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Oper Permission (Start Min Volt 2)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Oper Permission (Start Min Volt 3)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or less and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Oper Permission (Start Min Volt 4)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Oper Permission (Battery Current)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery discharge current is -125 A or less Engine stop and start ECU calculated value
      Oper Permission (Integrated Current)

      Permission of stop and start control based on the integrated current value conditions/

      NG / OK

      		 OK: Integrated current value more than specified The status depend on the value of "Integrated Current", and OK/NG threshold differs according to the battery temperature.
      Oper Prohibition (Jump Start)

      Prohibition of stop and start control based on the jump start conditions/

      Permit / Prohibit

      		 Prohibit: Engine started with the engine hood open and the ignition switch turned to START When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off.
      Oper Prohibition (Manual Start)

      Prohibition of stop and start control based on the manual start conditions/

      Permit / Prohibit

      		 Prohibit: During manual start

      When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off.

      Conditions for Manual Start:


      • Clutch start switch OFF or vehicle speed

      • Neutral position sensor (neutral position switch) OFF

      • Starter signal OFF

    NEXT

  3. READ VALUE USING GTS (OPER PERMISSION (BATTERY))

    Tech Tips

    Check whether stop and start control was prohibited based on the battery conditions or other conditions.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Battery)

      Permission of stop and start control based on the battery conditions

      NG / OK

      		 OK: Stop and start control is permitted due to battery condition, or Active Test (forced permission) is performed -
      Result
      Result Proceed to
      NG is displayed A
      OK is displayed B

    B

    END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

    A

  4. READ VALUE USING GTS (STATUS OF BATTERY CHARGE CONTROL)

    Tech Tips

    Check whether stop and start control was prohibited based on the battery charge control mode.


    1. Start the engine and allow it to idle.

    2. Enter the following menus: Powertrain / Stop and Start / Data List / Status of Battery Charge Control.

    3. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Status of Battery Charge Control

      Battery charge control status/

      Change Control Coordination Mode / Stop and Start Standalone Mode / Refresh Charge Mode / Stop and Start Restriction Mode / Temperature High / Low Mode / Abnormal Mode / Battery Condition Judgment Mode / Low Temperature Mode

      		 - -
      Result
      Result Proceed to
      "Refresh Charge Mode", "Battery Condition Judgment Mode" or "Abnormal Mode" is not displayed A
      "Refresh Charge Mode" is displayed B
      "Battery Condition Judgment Mode" is displayed C
      "Abnormal Mode" is displayed D

      Tech Tips

      If "Refresh Charge Mode" is displayed, leave the vehicle idling for 30 to 60 minutes.


    B

    END (STOP AND START CONTROL PROHIBITED IN REFRESH CHARGE MODE)

    C

    END (STOP AND START CONTROL PROHIBITED IN BATTERY CONDITION JUDGMENT MODE)

    D

    GO TO CHARGING SYSTEM Click here

    A

  5. READ VALUE USING GTS (OPER PERMISSION (START MIN VOLT 1, 2, 3, 4))

    Tech Tips

    Check whether stop and start control was prohibited based on the minimum starting voltage of the battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List.

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Start Min Volt 1)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or less and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Oper Permission (Start Min Volt 2)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage at starter ON is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Oper Permission (Start Min Volt 3)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or less and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Oper Permission (Start Min Volt 4)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery temperature is 0°C (32°F) or higher and the minimum voltage right after engine cranking is the threshold value or higher If 2 or more of Start Min Volt 1, 2, 3, or 4 are OK, stop and start control is permitted
      Result
      Result Proceed to
      OK is displayed for 2 or more items A
      OK is displayed for 1 item or none B

      1. The Data List item "Oper Permission (Start Min Volt 1, 2, 3, 4)" is judged OK or NG according to the values of the following Data List items.

        Stop and Start System
        GTS Display Measurement Item/Range Normal Condition Diagnostic Note
        Battery Temp (Start)

        Battery temperature at engine start/

        Min.: -40°C (-40°F), Max.: 100°C (212°F)

        		 Same as temperature around battery at engine start (after engine start) -
        Ambient Temp Sensor

        Ambient temperature/

        Min.: -80.0°C (-112.0°F), Max.: 79.9°C (175.8°F)

        		 Close to ambient temperature -
        Min Voltage(Cranking)

        Minimum battery voltage while engine cranking (incurrent trip)/

        Min.: 0.00 V, Max.: 327.67 V

        		 6 to 11 V Lowest battery voltage measured in a 5 second period after the starter starts operating.
        Min Volt(After Cranking)

        Minimum battery voltage just after engine cranking/

        Min.: 0.00 V, Max.: 327.67 V

        		 6 to 11 V Minimum battery voltage while starter driving
        Permission Criteria
        GTS Display Starting Battery Voltage Battery Temperature*1
        Oper Permission (Start Min Volt 1)*2 6.6 V or higher 0°C (32°F) or less
        Oper Permission (Start Min Volt 2)*2 6.6 V or higher Higher than 0°C (32°F)
        Oper Permission (Start Min Volt 3)*3 6.6 V or higher 0°C (32°F) or less
        Oper Permission (Start Min Volt 4)*3 6.6 V or higher Higher than 0°C (32°F)

        • *1: Read the Data List items "Battery Temp (Start)" and "Ambient Temp Sensor" when checking the battery temperature.

        • *2: Operation is permitted when the minimum voltage is 6.6 V or more when 0.0049 seconds have elapsed after cranking the engine.

        • *3: Operation is permitted when the minimum voltage is 6.6 V or more right after cranking the engine.


    B

    END (CHECK BATTERY CONDITION AND RECHARGE OR REPLACE BATTERY)

    A

  6. READ VALUE USING GTS (OPER PERMISSION (BATTERY CURRENT))

    Tech Tips

    Check whether the stop and start control was prohibited based on the battery discharge current battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery Current).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Battery Current)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Battery discharge current is -125 A or less Engine stop and start ECU calculated value
      Result
      Result Proceed to
      OK is displayed A
      NG is displayed B

      1. The Data List item "Oper Permission (Battery Current)" is judged OK or NG according to the values of the following Data List items.

        Stop and Start System
        GTS Display Measurement Item/Range Normal Condition Diagnostic Note
        Battery Current

        Battery current/

        Min.: -125.00 A, Max.: 124.99 A

        		 - -
        Permission Criteria
        GTS Display Battery Current
        Oper Permission (Battery Current) -125 A or less

    B

    END (REDUCE ELECTRICAL LOAD)

    A

  7. READ VALUE USING GTS (OPER PERMISSION (INTEGRATED CURRENT))

    Tech Tips

    Check whether the stop and start control was prohibited based on the integrated current value battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Integrated Current).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Integrated Current)

      Permission of stop and start control based on the integrated current value conditions/

      NG / OK

      		 OK: Integrated current value more than specified The condition is judged based on the integrated current value. The status depends on the value of "Integrated Current", and OK/NG threshold differs according to the battery temperature.
      Result
      Result Proceed to
      OK is displayed A
      NG is displayed B

    B

    READ VALUE USING GTS (INTEGRATED CURRENT) Click here

    A

  8. READ VALUE USING GTS (STATE OF BBC AND BBC CHECK RESULT)

    Tech Tips

    Check the operation of the backup boost converter.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / State of BBC and BBC Check Result.

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      State of BBC

      Backup boost converter status/

      Cycle Err / Overvol / Overload / Normal / Low Vol / Duty Err / S&S Sensor Electric Supply Low / S&S CPU Malfunction / BBC Overcurrent / S&S Starter Overcurrent / S&S Reduced Voltage Reset

      		 Normal: Backup boost converter operating normally

      • Cycle Err:


        • Abnormal output voltage cycle is detected

      • Overvol:


        • When the ignition switch is ON:


          1. Overvoltage is detected at the control IC power source within the backup boost converter

          2. Overheating is detected at the control IC power source within the backup boost converter


        • When boosting:


          1. Error is detected in the feedback circuit in the backup boost converter

          2. Too high or low output voltage


      • Overload:


        • Overcurrent is detected.


      • Low Vol:


        • A decrease in the voltage of the control IC power source within the backup boost converter is detected when ignition switch is turned to ON.


      • Duty Err:


        • Abnormal duty ratio is detected
      BBC Check Result

      Backup boost converter check result/

      Normal / Abnormal

      		 - -
      Result
      Result Proceed to
      Normal is displayed A
      Normal is not displayed B

    B

    GO TO BACKUP BOOST CONVERTER CIRCUIT

    A

  9. READ VALUE USING GTS (OPER PROHIBITION (JUMP START))

    Tech Tips

    Check whether stop and start control was prohibited based on the jump start battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Prohibition (Jump Start).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Prohibition (Jump Start)

      Prohibition of stop and start control based on the jump start conditions/

      Permit / Prohibit

      		 Prohibit: Engine started with the engine hood open and the ignition switch turned to START When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off.
      Result
      Result Proceed to
      Permit is displayed A
      Prohibit is displayed B

      1. The Data List item "Oper Permission (Jump Start)" is judged Permit or Prohibit according to the values of the following Data List items.

        Stop and Start System
        GTS Display Measurement Item/Range Normal Condition Diagnostic Note
        Hood Courtesy Switch

        Hood courtesy switch signal/

        ON / OFF

        ON: Engine hood closed

        OFF: Engine hood opened

        		 -
        Oper Permission (Engine Hood Closed)

        Permission of stop and start control based on the engine hood open/close conditions/

        NG / OK

        		 OK: Engine hood closed -
        Permission Criteria
        GTS Display Conditions
        Oper Prohibition (Jump Start) ON (Engine hood closed) is displayed for Hood Courtesy Switch
        OK (Engine Hood Closed) is displayed for Oper Permission (Engine Hood Closed)

    B

    READ VALUE USING GTS (HOOD COURTESY SWITCH) Click here

    A

  10. READ VALUE USING GTS (OPER PROHIBITION (MANUAL START))

    Tech Tips

    Check whether the stop and start control was prohibited based on the manual start battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Prohibition (Manual Start).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Prohibition (Manual Start)

      Prohibition of stop and start control based on the manual start conditions/

      Permit / Prohibit

      		 Prohibit: During manual start

      When Prohibit is displayed, the stop and start control will be prohibited until the ignition switch is turned off. Conditions for Manual Start:


      • Clutch start switch OFF or vehicle speed signal input

      • Neutral position sensor (neutral position switch) OFF

      • Starter signal OFF
      Result
      Result Proceed to
      Permit is displayed A
      Prohibit is displayed B

    B

    END (STOP AND START CONTROL PROHIBITED DUE TO MANUAL START OPERATION)

    A

  11. READ VALUE USING GTS (OPER PERMISSION (BATTERY))

    Tech Tips

    Check whether the stop and start control was prohibited based on the battery temperature battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Battery)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Stop and start control is permitted based on battery conditions, or Active Test (forced permission) is performed -
      Result
      Result Proceed to
      NG is displayed A
      OK is displayed B

      1. The Data List item "Oper Permission (Battery)" is judged OK or NG according to the values of the following Data List items.

        Stop and Start System
        GTS Display Measurement Item/Range Normal Condition Diagnostic Note
        Battery Temp (Start)

        Battery temperature at engine start/

        Min.: -40°C (-40°F), Max.: 100°C (212°F)

        		 Same as temperature around battery at engine start (after engine start) -
        Ambient Temp Sensor

        Ambient temperature/

        Min.: -80.0°C (-112.0°F), Max.: 79.9°C (1175.8°F)

        		 Close to ambient temperature -
        Permission Criteria
        GTS Display Conditions
        Oper Permission (Battery Current) Current battery temperature is between -10°C (14°F) and 70°C (158°F)

        Tech Tips

        *: Read the Data List items "Battery Temp (Start)" and "Ambient Temp Sensor" when checking the battery temperature.


    B

    END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

    A

  12. READ VALUE USING GTS (BATTERY TEMP (START))

    Tech Tips

    Check the battery temperature.


    1. Enter the following menus: Powertrain / Stop and Start / Data List.

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Battery Temp (Start)

      Battery temperature at engine start/

      Min.: -40°C (-40°F), Max.: 100°C (212°F)

      		 Same as temperature around battery at engine start (after engine start) -
      Ambient Temp Sensor

      Ambient temperature/

      Min.: -80.0°C (-112.0°F), Max.: 79.9°C (175.8°F)

      		 Close to ambient temperature -
      Result
      Result Proceed to
      Battery temperature is as specified A
      Battery temperature is not as specified B

      Tech Tips

      If the battery temperature is not as specified, leave the battery under room temperature conditions until its temperature becomes as specified.


    B

    END (STOP AND START CONTROL PROHIBITED DUE TO ABNORMAL BATTERY TEMPERATURE)

    A

  13. READ VALUE USING GTS (OPER PERMISSION (BATTERY))

    Tech Tips

    Check whether stop and start control was prohibited based on the alternator status battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Battery)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Stop and start control is permitted based on battery conditions, or Active Test (forced permission) is performed -
      Result
      Result Proceed to
      NG is displayed A
      OK is displayed B

      1. The Data List item "Oper Permission (Battery)" is judged OK or NG according to the values of the following Data List items.

        Stop and Start System
        GTS Display Measurement Item/Range Normal Condition Diagnostic Note
        Alternator Status

        Alternator power generation status/

        Normal / Abnormal

        		 Normal: Alternator operation normal -
        Permission Criteria
        GTS Display Conditions
        Oper Permission (Battery) Normal is displayed for Alternator Status (Alternator is generating power)
        Charge indicator light is off when the engine is running (Alternator is generating power)

    B

    END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

    A

  14. READ VALUE USING GTS (ALTERNATOR STATUS)

    Tech Tips

    Check the power generation status of the alternator.


    1. Start the engine and allow it to idle.

    2. Enter the following menus: Powertrain / Stop and Start / Data List / Alternator Status.

    3. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Alternator Status

      Alternator power generation status/

      Normal / Abnormal

      		 Normal: Alternator operation normal -
      Result
      Result Proceed to
      Normal is displayed A
      Abnormal is displayed B

    B

    GO TO CHARGING SYSTEM Click here

    A

  15. READ VALUE USING GTS (OPER PERMISSION (BATTERY))

    Tech Tips

    Check whether stop and start control was prohibited based on the idling stop rate battery condition.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Oper Permission (Battery).

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Oper Permission (Battery)

      Permission of stop and start control based on the battery conditions/

      NG / OK

      		 OK: Stop and start control is permitted based on battery conditions, or Active Test (forced permission) is performed -
      Result
      Result Proceed to
      NG is displayed A
      OK is displayed B

      1. The Data List item "Oper Permission (Battery)" is judged OK or NG according to the values of the following Data List items.

        Stop and Start System
        GTS Display Measurement Item/Range Normal Condition Diagnostic Note
        Idling Stop Rate

        Rate of the idling stop time to the entire ignition switch ON time/

        Min.: 0%, Max.: 100%

        		 - -
        Permission Criteria
        GTS Display Idling Stop Rate
        Oper Permission (Battery) 39% or less

        Tech Tips

        When the idling stop rate exceeds 40%, stop and start control is permitted when the rate drops to 37% or less.


    B

    END (CHECK OTHER STOP AND START CONTROL PERMISSION/PROHIBITION CONDITIONS)

    A

  16. READ VALUE USING GTS (IDLING STOP RATE)

    Tech Tips

    Check the idling stop rate.


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Idling Stop Rate.

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Idling Stop Rate

      Rate of the idling stop time to the entire ignition switch ON time/

      Min.: 0%, Max.: 100%

      		 - -
      Result
      Result Proceed to
      40% or higher A
      39% or less B

      Tech Tips

      When the idling stop rate exceeds 40%, turn the ignition switch off and then start the engine again. If NG is still displayed for the Data List item "Oper Permission (Battery)", the battery may be discharged or deteriorated. Check the battery condition and recharge or replace the battery.


    A

    END (STOP AND START CONTROL PROHIBITED DUE TO HIGH IDLING STOP RATE (40% OR MORE))

    B

    END (CHECK BATTERY CONDITION AND RECHARGE OR REPLACE BATTERY)

  17. READ VALUE USING GTS (HOOD COURTESY SWITCH)

    Tech Tips

    Check the engine hood courtesy switch (hood lock assembly).


    1. Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.

    2. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Hood Courtesy Switch

      Hood courtesy switch signal/

      ON / OFF

      ON: Engine hood closed

      OFF: Engine hood opened

      		 -

      Tech Tips

      When the result is OK, the engine may have been started with the engine hood open to perform a jump start. Close the engine hood and start the engine again.


    OK

    END (STOP AND START CONTROL PROHIBITED DUE TO ENGINE START WITH ENGINE HOOD OPEN)

    NG

    GO TO ENGINE HOOD COURTESY SWITCH CIRCUIT

  18. READ VALUE USING GTS (INTEGRATED CURRENT)

    Tech Tips

    Judge the battery condition based on the integrated current value.


    1. Start the engine and allow it to idle.

    2. Enter the following menus: Powertrain / Stop and Start / Data List / Integrated Current.

    3. Check the following items on the GTS display.

      Stop and Start System
      GTS Display Measurement Item/Range Normal Condition Diagnostic Note
      Integrated Current

      Battery integrated current/

      Min.: -268434.45 A-sec, Max.: 268435.45 A-sec

      		 Differs according to the vehicle condition (charge / discharge conditions) -

      1. Judge whether the Data List item "Integrated Current" is OK or NG according to the following table.

        Stop and Start System
        GTS Display Measurement Item/Range Normal Condition Diagnostic Note
        Battery Temp (Start)

        Battery temperature at engine start/

        Min.: -40°C (-40°F), Max.: 100°C (212°F)

        		 Same as temperature around battery at engine start (after engine start) -
        Idle

        Battery temperature at engine start/

        ON / OFF

        ON: Accelerator pedal fully released

        OFF: Accelerator pedal depressed

        		 This is sent from the ECM.
        Battery Current

        Battery current/

        Min.: -125.00 A, Max.: 124.99 A

        		 - -
        Ambient Temp Sensor

        Ambient temperature/

        Min.: -80.0°C (-112.0°F), Max.: 79.9°C (175.8°F)

        		 Close to ambient air temperature -
        Integrated Current

        Battery integrated current/

        Min.: -268434.45 A-sec, Max.: 268435.45 A-sec

        		 Differs according to the vehicle condition (charge/discharge conditions) -
        Standard Integrated Current Value
        Battery Temperature GTS Display Integrated Current Proceed to
        -1°C (30.2°F) or higher, or 65°C (149°F) or less Integrated Current Below -5299 A-sec A
        -1°C (30.2°F) or higher, or 65°C (149°F) or less Below 0 A-sec A
        Below -1°C (30.2°F) or -15°C (5°F) or higher, or 65°C (149°F) or higher, or 75°C (167°F) or less
        Below -15°C (5°F) or higher than 75°C (167°F) - B
        Cause and Action to be Taken
        Result Cause Action to be Taken
        A Integrated current value is limited for the stop and start control due to discharge or deterioration of the battery Check the battery condition and recharge or replace the battery
        B Integrated current value is limited for stop and start control due to battery temperature (too high/low) Leave the battery under room temperature conditions until its temperature becomes as specified. Then check the battery condition and recharge or replace the battery.

        • After recharging the battery, initialize the integrated current value* and drive the vehicle until stop and start control operation is permitted (approximately 15 to 40 minutes).

          *: Disconnect the cables from the battery, wait for 30 seconds or more and then reconnect the cables.

        • When the battery sensor current value is normal, recharge or replace the battery.


    NEXT

    END (RECHARGE OR REPLACE BATTERY)