OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK

      Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Forward position A Moves from A to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Forward position A Does not move Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Position between forward position A and driving position C Moves from B to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Position between forward position A and driving position C Moves from B to forward position A Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Driving position C Moves from C to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Driving position C Does not move Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Position between driving position C and retracted position E Moves from D to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Position between driving position C and retracted position E Moves from D to driving position C Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Retracted position E Does not move Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Retracted position E Moves from E to driving position C

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      
      

      • Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the outer rear view mirror assembly LH.

   2. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Apply battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Battery positive (+) → Terminal 7 (MV) Battery negative (-) → Terminal 8 (M+) Turns upward Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 7 (MV) Turns downward Battery positive (+) → Terminal 9 (MH) Battery negative (-) → Terminal 8 (M+) Turns left Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 9 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly LH.

   3. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the mirror heater.

      
      

      1. Measure the resistance according to the value (s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition Terminal 6 (+) - Terminal 17 (-) 25°C (75°F) 3.0 to 3.9 Ω

         If the result is not as specified, replace the outer rear view mirror assembly LH.

      2. Apply battery voltage and check the operation of the mirror heater.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (+) Battery negative (-) → Terminal 17 (-) Mirror becomes warm

         Tech Tips

         It will take a short time for the mirror to become warm.

         If the result is not as specified, replace the outer rear view mirror assembly LH.

   4. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the side turn light assembly.

      
      

      1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

         OK
         Measurement Connection Specified Condition Battery positive (+) → Terminal 4 (TRNL) Negative (-) end of the battery → Terminal 15 (GND) Side turn light illuminates

         
         

         • If the result is not as specified, check the side turn signal light assembly LH Click here.

         • If the result is not as specified, replace the outer rear view mirror assembly LH.

   5. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the EC mirror operation.

      
      

      1. Connect 1.5 V dry-cell battery.

      2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (EC+) Battery negative (-) → Terminal 16 (EC-) Mirror surface becomes dark

         If the result is not as specified, replace the outer rear view mirror assembly LH.

2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

      OK

      Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Forward position A Moves from A to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Forward position A Does not move Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Position between forward position A and driving position C Moves from B to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Position between forward position A and driving position C Moves from B to forward position A Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Driving position C Moves from C to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Driving position C Does not move Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Position between driving position C and retracted position E Moves from D to retracted position E Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Position between driving position C and retracted position E Moves from D to driving position C Battery positive (+) → Terminal 19 (MR) Battery negative (-) → Terminal 20 (MF) Retracted position E Does not move Battery negative (-) → Terminal 19 (MR) Battery positive (+) → Terminal 20 (MF) Retracted position E Moves from E to driving position C

      Note

      
      

      • Disconnect and reconnect the battery between each mirror position check.

      
      

      • Do not apply battery voltage when moving the mirror by hand into each mirror position.

      If the result is not as specified, replace the outer rear view mirror assembly RH.

   2. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Apply battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Battery positive (+) → Terminal 7 (MV) Battery negative (-) → Terminal 8 (M+) Turns upward Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 7 (MV) Turns downward Battery positive (+) → Terminal 9 (MH) Battery negative (-) → Terminal 8 (M+) Turns left Battery negative (-) → Terminal 8 (M+) Battery positive (+) → Terminal 9 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly RH.

   3. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the mirror heater.

      
      

      1. Measure the resistance according to the value (s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition Terminal 6 (+) - Terminal 17 (-) 25°C (75°F) 3.0 to 3.9 Ω

         If the result is not as specified, replace the outer rear view mirror assembly RH.

      2. Apply battery voltage and check the operation of the mirror heater.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (+) Battery negative (-) → Terminal 17 (-) Mirror becomes warm

         Tech Tips

         It will take a short time for the mirror to become warm.

         If the result is not as specified, replace the outer rear view mirror assembly.

   4. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the side turn light assembly.

      
      

      1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

         OK
         Measurement Connection Specified Condition Battery positive (+) → Terminal 4 (TRNR) Negative (-) end of the battery → Terminal 15 (GND) Side turn light illuminates

         
         

         • If the result is not as specified, check the side turn signal light assembly RH Click here.

         • If the result is not as specified, replace the outer rear view mirror assembly RH.

   5. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the EC mirror operation.

      
      

      1. Connect 1.5 V dry-cell battery.

      2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (EC+) Battery negative (-) → Terminal 16 (EC-) Mirror surface becomes dark

         If the result is not as specified, replace the outer rear view mirror assembly RH.