POWER WINDOW CONTROL SYSTEM Rear Power Window LH Auto Up / Down Function does not Operate with Rear Power Window Switch LH

DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate Click here.

WIRING DIAGRAM

A01WT1SE16
*a Rear Power Window Regulator Switch Assembly LH
*b Rear Power Window Regulator Motor Assembly LH

CAUTION / NOTICE / HINT

Note


  • If the rear power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system Click here.

  • Check that the "RL Window Auto Up" and "RL Window Auto Down" power window control system customize settings are "ON" before proceeding with work Click here.

  • After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.

Tech Tips

If the pulse sensor built into the rear power window regulator motor assembly LH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly LH at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly LH Click here.

PROCEDURE


  1. CHECK FOR DTC


    1. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC is not output A
      B2311 is output B
      B2312 is output C
      B2313 is output D
      LIN communication system DTCs are output E

    B
    C
    D
    E
    A
  2. CHECK MANUAL UP/DOWN FUNCTION (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)


    1. Check that the manual up/down function using the rear power window regulator switch can operate the rear door power window LH Click here.

      OK
      Manual up/down function operates.

    NG
    OK
  3. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR LH)


    1. Use the Data List to check if the power window regulator motor is functioning properly Click here.

      RL-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RL Door P/W Auto SW Rear power window LH auto up/down signal / ON or OFF

      ON: Rear power window LH auto up/down switch operated

      OFF: Rear power window LH switch not operated

      -
      OK
      Display changes according to operation of rear power window switch LH.

    OK
    NG
  4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)


    1. A01WUGLE01
      *1 Front view of wire harness connector: (to Power Window Regulator Switch)
      *2 Front view of wire harness connector: (to Power Window Regulator Motor)

      Disconnect the J20 switch connector.

    2. Disconnect the J11 motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J20-4 (AUTO) - J11-4 (AUTO) Always Below 1 Ω
      J20-4 (AUTO) or J11-4 (AUTO) - Body ground Always 10 kΩ or higher

    NG
    OK
  5. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

    A01WVI0E07
    *1 Component without harness connected: (Rear Power Window Regulator Switch)

    1. Remove the rear power window regulator switch LH Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      4 (AUTO) - 5 (GND) Auto up/down operation Below 1 Ω

    OK
    NG