POWER WINDOW CONTROL SYSTEM Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION


WIRING DIAGRAM

A01WUU9E01

CAUTION / NOTICE / HINT

Note


  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly Click here.

  • If the front power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system Click here.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK LIN COMMUNICATION SYSTEM


    1. Check for LIN communication system DTCs related to the power window control system Click here.

      OK
      LIN communication system DTCs are not output.

    NG

    GO TO LIN COMMUNICATION SYSTEM Click here

    OK

  2. CHECK FOR DTC (B2312)


    1. Check if DTC B2312 is output Click here.

      OK
      DTC B2312 is not output.

    NG

    GO TO DTC B2312 Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR MOTOR)


    1. Use the Data List to check if the power window regulator motor is functioning properly Click here.

      D-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Up SW Driver side power window manual up signal / ON or OFF

      ON: Driver side power window manual up switch operated

      OFF: Driver side power window switch not operated

      		 -
      D Door P/W Down SW Driver side power window manual down signal / ON or OFF

      ON: Driver side power window manual down switch operated

      OFF: Driver side power window switch not operated

      		 -
      OK
      Display changes according to operation of multiplex network master switch.
      Result
      Result Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    C

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    A

  4. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)


    1. A01WSVAE01

      Disconnect the I11*1 or I22*2 switch connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      I11-11 (B) - Body ground Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      I22-11 (B) - Body ground Always 11 to 14 V
      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      I11-12 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      I22-12 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)


    1. A01WW6LE01

      Disconnect the I12*1 or I4*2 motor connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      I12-2 (B) - Body ground Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      I4-2 (B) - Body ground Always 11 to 14 V
      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      I12-1 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      I4-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)


    1. A01WV32E01

      Disconnect the I11*1 or I22*2 switch connector.

    2. Disconnect the I12*1 or I4*2 motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      I11-20 (UP) - I12-10 (UP) Always Below 1 Ω
      I11-15 (DOWN) - I12-7 (DOWN) Always Below 1 Ω
      I11-20 (UP) or I12-10 (UP) - Body ground Always 10 kΩ or higher
      I11-15 (DOWN) or I12-7 (DOWN) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      I22-20 (UP) - I4-10 (UP) Always Below 1 Ω
      I22-15 (DOWN) - I4-7 (DOWN) Always Below 1 Ω
      I22-20 (UP) or I4-10 (UP) - Body ground Always 10 kΩ or higher
      I22-15 (DOWN) or I4-7 (DOWN) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

    A

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    C

    INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    B

  7. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. Remove the front power window regulator motor LH Click here.

    2. Inspect the front power window regulator motor LH Click here.


    OK

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

  8. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    1. Remove the front power window regulator motor RH Click here.

    2. Inspect the front power window regulator motor RH Click here.


    OK

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here