AIR CONDITIONING SYSTEM, Diagnostic DTC:B1447/47

DTC Code DTC Name
B1447/47 Rear Air Mix Damper Control Servo Motor Circuit on Driver Side

DESCRIPTION


The rear air mix damper servo motor LH*1or RH*2 sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air mix damper servo motor LH*1or RH*2 to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.

Tech Tips

Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.

DTC Code DTC Detection Condition Trouble Area
B1447/47 The rear air mix damper position does not change even if the air conditioning amplifier assembly operates the rear air mix damper servo motor.

  • Rear air mix damper servo motor LH*1

  • Rear air mix damper servo motor RH*2

  • No. 2 air conditioning harness assembly

  • Harness or connector

  • Air conditioning amplifier assembly

WIRING DIAGRAM

B0018TIE18

PROCEDURE


  1. READ VALUE USING GTS (AIR MIX SERVO TARG PLS [R], A/M SERVO ACTUAL PULSE[R])


    • *1: for LHD

    • *2: for RHD


    1. Use the Data List to check if the rear air mix damper servo motor LH*1 or RH*2 is functioning properly Click here.

      Air Conditioner
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Air Mix Servo Targ Pls(R) Rear air mix damper servo motor LH*1 or RH*2 target pulse / Min.: 128, Max.: 383

        for LHD:

      • MAX COLD: 254 (pulse)

      • MAX HOT: 299 (pulse)


        for RHD:

      • MAX COLD: 258 (pulse)

      • MAX HOT: 213 (pulse)

      • Displayed between 254 and 299 pulse (for LHD)

      • Displayed between 213 and 258 pulse (for RHD)

      • Rear air mix damper servo motor LH*1 or RH*2 system malfunction
      Air Mix Servo Actual Pluse(R) Rear air mix damper servo motor LH*1 or RH*2 actual pulse / Min.: 128, Max.: 383

        for LHD:

      • MAX COLD: 254 (pulse)

      • MAX HOT: 299 (pulse)


        for RHD:

      • MAX COLD: 258 (pulse)

      • MAX HOT: 213 (pulse)

      • Displayed between 254 and 299 pulse (for LHD)

      • Displayed between 213 and 258 pulse (for RHD)

      • Rear air mix damper servo motor LH*1 or RH*2 system malfunction
      OK
      When the rear temperature adjust switch for driver side is turned from MAX COLD and MAX HOT, the actual pulse changes following the target pulse.
      Result
      Result Proceed to
      Target pulse changes but actual pulse does not change A
      Target pulse and actual pulse do not change B
      Actual pulse changes following the target pulse (When troubleshooting according to the DTC) C
      Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) D

    B

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    C

    CHECK FOR DTC Click here

    D

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    A

  2. CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. Disconnect the K19 No. 2 air conditioning harness assembly connector.

    2. Disconnect the E36 air conditioning amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K19-2 (RBUG) - E36-12 (RBUG) Always Below 1 Ω
      K19-3 (RBUS) - E36-13 (RBUS) Always Below 1 Ω
      K19-4 (RBBU) - E36-14 (RBBU) Always Below 1 Ω
      K19-2 (RBUG) or E36-12 (RBUG) - Body ground Always 10 kΩ or higher
      K19-3 (RBUS) or E36-13 (RBUS) - Body ground Always 10 kΩ or higher
      K19-4 (RBBU) or E36-14 (RBBU) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK REAR AIR MIX DAMPER SERVO MOTOR (for Driver Side)


    1. Replace the rear air mix damper servo motor LH*1 or RH*2 Click here.


      • *1: for LHD

      • *2: for RHD

      Tech Tips

      Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.

    2. Clear the DTCs Click here.

    3. Check for DTCs Click here.

      OK
      DTC B1447/47 is not output.

    OK

    END (REAR AIR MIX DAMPER SERVO MOTOR [for Driver Side] WAS DEFECTIVE)

    NG

  4. CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY


    1. Replace the No. 2 air conditioning harness assembly with a new or known good one Click here.

    2. Clear the DTCs Click here.

    3. Check for DTCs Click here.

      OK
      DTC B1447/47 is not output.

    OK

    END (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  5. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      OK
      DTC B1447/47 is not output.

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here