REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 60 Side) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.

PROCEDURE


  1. INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


    1. B001A64

      Attach the guide and install the 6 screws and seat climate control blower LH.

  2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

    B0019HI

    1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

    2. Tighten the 5 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Using a T40 "TORX" socket, tighten the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL NO. 1 SEAT LEG ASSEMBLY LH

    B001AYU

    1. Using a T40 "TORX" socket, install the seat leg assembly with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  4. INSTALL REAR SEAT INNER BELT ASSEMBLY

    Click here

  5. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

    B0019TX

    1. Attach the 2 claws to install the seat heater control.

  6. INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)

    B0018YJ

    1. Install the holder bracket with the 2 screws.

    2. Connect the seat wire connector.

  7. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    1. B00187U

      Attach the clamp to install the seat lock cable.

    2. Attach the 3 cable clamps to connect the 3 cables.

    3. Connect the cable and install a new cable tie.

    4. B001A9P

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  8. INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


    1. B0018R0

      Attach the 2 hooks.

    2. Install the screw and seat climate control blower LH.

  9. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH


    1. B0018IH

      Install the lower seatback cover.

    2. B0018SF

      Temporarily install the seatback frame with the 4 bolts.

    3. for LH Side:

      Using a T40 "TORX" socket, tighten the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. for RH Side:

      Using a T55 "TORX" socket, tighten the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  10. INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

    B00184E

    1. Attach the clamp to install the lock control cable.

    2. Attach the 2 cable clamps to connect the cable.

  11. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH

    B0019YT

    1. Attach the clamp to install the adjusting cable.

    2. Attach the 2 cable clamps to connect the cable.

  12. INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    Click here

  13. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

    Click here

  14. INSTALL REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH

    B0018Q5

    1. Attach the 4 claws to install the cover.

    2. Install the 4 screws.

  15. INSTALL REAR SEATBACK HINGE COVER LH

    B00199U

    1. Attach the claw to install the cover.

    2. Install the screw.

  16. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    B001AIT

    1. Attach the claw to install the cover.

    2. Install the screw.

  17. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

    B001912

    1. Attach the clamp to install the cover.

    2. Install the screw.

  18. INSTALL REAR SEAT RECLINING COVER LH

    B0018N6

    1. Attach the claw to install the cover.

    2. Install the screw.

  19. INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY


    1. Attach the claw and install the rear seat center armrest cup holder sub-assembly.

  20. INSTALL SEAT CENTER ARMREST BRACKET SUB-ASSEMBLY

  21. INSTALL SEAT SWITCH WIRING SUB-ASSEMBLY (w/ Climate Control Seat System)


    1. Set the seat switch wiring sub-assembly.

    2. B001861

      Install the clamp and seat switch wiring sub-assembly.

  22. INSTALL REAR SEAT CENTER ARMREST DOOR SUB-ASSEMBLY


    1. B001B4J

      Install the 2 nuts and rear seat center armrest door sub-assembly.

    2. Attach the 3 clips.

  23. INSTALL REAR SEATBACK MOULDING RH


    1. B001847

      Attach the guide and claw to install the rear seatback moulding RH.

  24. INSTALL REAR SEATBACK MOULDING LH


    1. B001AEO

      Attach the guide and claw to install the rear seatback moulding LH.

    2. w/ Climate Control System:


      1. B001APG

        Push in the rear seat switch wiring sub-assembly.

    3. B0019ZV

      Attach the 5 clips and 2 claws to install the rear seatback moulding LH.

  25. INSTALL REAR SEAT CENTER ARMREST BOX ASSEMBLY

  26. INSTALL REAR SEAT CENTER ARMREST PANEL SUB-ASSEMBLY (w/o Climate Control Seat System)

  27. INSTALL COOLER CONTROL SWITCH ASSEMBLY (w/ Climate Control Seat System)

    Click here

  28. INSTALL REAR CENTER SEAT ARMREST ASSEMBLY

    B001AR8

    1. Using a T40 "TORX" socket, install the center seat armrest with the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  29. INSTALL SEATBACK STOPPER PLATE


    1. Install the bush to the stopper plate.

    2. B00193N

      Temporarily install the stopper plate with the 3 bolts.

    3. Using a T40 "TORX" socket, tighten the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    4. Tighten the bolt.

      Torque:
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

  30. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

  31. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

    Click here

  32. INSTALL REAR SEPARATE TYPE SEATBACK COVER


    1. B0019V4E01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. B0019IE

      Connect the seatback cover bracket to the seatback pad.

  33. INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. B0018GB

      Pull out the seat belt.

    3. Pass the side airbag wire harness through the hole in the seatback.

    4. w/ Seat Heater System:


      1. B0018Z1

        Pass the seatback heater wire harness through the hole in the seatback.

      2. B001AN3E01
        *1 Cable Tie

        Connect the seatback heater wire harness and install a new cable tie.

    5. B0019ZY

      Install the seatback cover bracket to the seat frame with the cap nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    6. B001AJIE01
      *1 Hog Ring Pliers

      Using hog ring pliers, install new hog rings to the seatback frame.

  34. INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

    B001AD3

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  35. INSTALL SHOULDER BELT ANCHOR COVER

    B0019Y2

    1. Attach the 2 claws to install the cover.

  36. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    B0019D9

    1. Attach the 4 claws to install the 2 supports.

  37. INSTALL REAR SEAT HEADREST ASSEMBLY

  38. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

    B001AA9

    1. Push the board down to attach the 2 claws on the bottom.

    2. Attach the 2 claws on the top of the board to install it.

  39. INSTALL REAR SEATBACK COVER

    B001AI1

    1. Attach the 4 claws to install the cover.

  40. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

    Click here

  41. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    B0019BDE01
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. B0018KIE01
      *1 Fastening Tape

      Attach the 3 pieces of fastening tape.

  42. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. B0018TM

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. B001A8D

        Connect the 2 seat heater connectors.

    4. Attach the side airbag wire harness clamps.

  43. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    Click here

  44. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  45. INSTALL REAR SEAT UNDER TRAY COVER LH

    B0019Q0

    1. Install the cover with the 2 screws.

  46. INSTALL REAR SEAT CUSHION COVER RH

    B001B08

    1. Attach the 2 claws to install the cover.

    2. Install the 4 screws.

  47. INSTALL REAR POWER SEAT SWITCH


    1. Install the power seat switch with the 2 screws.

  48. INSTALL NO. 1 SEAT CUSHION PLATE

    B001838

    1. Attach the 3 claws to install the seat cushion plate.

  49. INSTALL REAR UNDER SIDE COVER LH

    B0018VY

    1. Attach the 2 claws and 2 clips to install the cover.

    2. Install the 5 screws.

    3. B0018VB

      Attach the 10 claws.

  50. INSTALL REAR SEATBACK STAY COVER LH

    B0018DQ

    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  51. INSTALL SEAT BELT ANCHOR COVER CAP


    1. B001AW5

      Install the anchor cover cap with the screw.

    2. B0019NJ

      Attach the claw to close the cap.

  52. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

    B0019ZN

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  53. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. B00196T

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Attach the wire harness clamp.

    3. w/ Seat Heater System:

      Attach the wire harness clamp.

  54. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach the 2 claws to close the protector.

    2. B001834

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. B001AQM

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  55. INSTALL REAR SEAT SIDE HINGE MALE COVER RH


    1. B00187L

      Attach the clip to install the cover.

  56. INSTALL REAR SEAT SIDE HINGE MALE COVER LH


    1. Attach the clip to install the cover.

  57. INSTALL REAR SEAT SIDE HINGE FEMALE COVER


    1. B00187Q

      Attach the 6 claws to install the 2 covers.

  58. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY


    1. Install the fold seat stopper band to the seat leg side cover.

  59. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. B0019NV

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. B0018CZ

      Attach the 4 claws to install the seat leg side cover.

    3. Install the 4 screws.

  60. INSTALL NO. 1 SEAT CUSHION COVER

    B0019FZ

    1. Attach the 4 claws to install the 2 covers.

  61. INSTALL UPPER SEAT TRACK RAIL COVER RH

    B00190P

    1. Attach the 2 claws to install the cover.

  62. INSTALL UPPER SEAT TRACK RAIL COVER LH

    B0018Z8

    1. Attach the 2 claws to install the cover.

  63. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    B00195H

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  64. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    B0018MAE01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  65. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

    B0019I4

    1. Install the release handle with the screw.

  66. INSTALL SEAT ADJUSTER BOLT COVER

    B001A93

    1. Attach the 2 claws to install the cover.