REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 40 Side) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.

PROCEDURE


  1. INSTALL SEAT CLIMATE CONTROL BLOWER RH (w/ Climate Control Seat System)


    1. B001A64

      Attach the hook and install the 6 screws to climate control blower RH.

  2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

    A01WPN5

    1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

    2. Tighten the 5 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Using a T40 "TORX" socket, tighten the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

    Click here

  4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

    B0019TX

    1. Attach the 2 claws to install the seat heater control.

  5. INSTALL REAR SEAT CUSHION HOLDER BRACKET RH (w/ Seat Heater System)

    A01WR00

    1. Install the holder bracket with the 2 screws.

    2. Connect the seat wire connector.

  6. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

    A01WVE4

    1. Attach the clamp to install the seat lock cable.

    2. Attach the 3 cable clamps to connect the 3 cables.

    3. A01WQUO

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    4. A01WSXL

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

    A01WPYY

    1. Install the 2 fold seat lock control cables.

    2. Attach the 2 cable clamps to connect the 2 cables.

  8. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

    A01WQG6

    1. Temporarily install the seatback frame with the 4 bolts.

    2. Using a T40 "TORX" socket, tighten the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  9. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

    A01WVKM

    1. Attach the clamp to install the lock control cable.

    2. Attach the 2 cable clamps to connect the cable.

  10. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY RH

    A01WSA7

    1. Attach the clamp to install the adjusting cable.

    2. Attach the 2 cable clamps to connect the cable.

  11. INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


    1. B0018R0

      Attach the hook.

    2. Install the screw and seat climate control blower RH.

    3. Connect the connector.

  12. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A01WSMY

    1. Attach the claw to install the cover.

    2. Install the screw.

  13. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

    B001912

    1. Attach the clamp to install the cover.

    2. Install the screw.

  14. INSTALL REAR SEAT RECLINING COVER RH

    B0018N6

    1. Attach the claw to install the cover.

    2. Install the screw.

  15. INSTALL REAR SEAT RECLINING COVER LH


    1. Attach the claw to install the cover.

    2. Install the screw.

  16. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

    Click here

  17. INSTALL REAR SEPARATE TYPE SEATBACK COVER

    A01WSFYE01
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01WQF7

      Connect the seatback cover bracket to the seatback pad.

  18. INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. Pass the side airbag wire harness through the hole in the seatback.

    3. w/ Seat Heater System:


      1. A01WVD6

        Pass the seatback heater wire harness through the hole in the seatback.

      2. B00199EE01
        *1 Cable Tie

        Connect the seatback heater wire harness and install a new cable tie.

    4. A01WUPT

      Install the seatback cover bracket to the seat frame with the cap nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    5. A01WPC5E01
      *1 Hog Ring Pliers

      Using hog ring pliers, install new hog rings to the seatback frame.

  19. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    B0019D9

    1. Attach the 4 claws to install the 2 supports.

  20. INSTALL REAR SEAT HEADREST ASSEMBLY

  21. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

    A01WPA9

    1. Push the board down to attach the 2 claws on the bottom.

    2. Attach the 2 claws on the top of the board to install it.

  22. INSTALL REAR SEATBACK COVER

    B001AI1

    1. Attach the 4 claws to install the cover.

  23. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

    Click here

  24. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    A01WVY8E01
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. B0019PYE01
      *1 Fastening Tape

      Attach the 3 pieces of fastening tape.

  25. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A01WQ3O

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A01WW6U

        Connect the 2 seat heater connectors.

    4. Attach the side airbag wire harness clamps.

  26. INSTALL REAR SEAT UNDER TRAY COVER RH

    B0019Q0

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  27. INSTALL REAR POWER SEAT SWITCH


    1. Install the power seat switch with the 2 screws.

  28. INSTALL NO. 1 SEAT CUSHION PLATE

    B001838

    1. Attach the 3 claws to install the seat cushion plate.

  29. INSTALL REAR UNDER SIDE COVER LH

    A01WWID

    1. Attach the 2 claws and clip to install the cover.

    2. Install the 5 screws.

  30. INSTALL REAR SEAT COVER

    A01WWR5

    1. Attach the 2 claws to install the cover.

    2. Install the 3 screws.

    3. A01WW9T

      Attach the 12 claws.

  31. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. A01WR0H

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Attach the wire harness clamp.

    3. w/ Seat Heater System:

      Attach the wire harness clamp.

  32. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

    A01WVBZ

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  33. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach the 2 claws to close the protector.

    2. A01WPZW

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A01WVPG

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  34. INSTALL REAR SEAT SIDE HINGE MALE COVER RH

    B00187L

    1. Attach the clip to install the cover.

  35. INSTALL REAR SEAT SIDE HINGE MALE COVER LH


    1. Attach the clip to install the cover.

  36. INSTALL REAR SEAT SIDE HINGE FEMALE COVER

    B00187Q

    1. Attach the 6 claws to install the 2 covers.

  37. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY


    1. Install the fold seat stopper band to the seat leg side cover.

  38. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A01WS94

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A01WSEZ

      Attach the 3 claws to install the seat leg side cover.

    3. Install the 4 screws.

  39. INSTALL NO. 1 SEAT CUSHION COVER

    A01WWXD

    1. Attach the 4 claws to install the 2 covers.

  40. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A01WR6N

    1. Attach the 2 claws to install the cover.

  41. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01WV5N

    1. Attach the 2 claws to install the cover.

  42. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A01WTIN

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  43. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A01WTMHE01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  44. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

    A01WTWG

    1. Install the release handle with the screw.

  45. INSTALL SEAT ADJUSTER BOLT COVER

    A01WSLP

    1. Attach the 2 claws to install the cover.