REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 60 Side) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.

PROCEDURE


  1. INSTALL REAR SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY


    1. Install the 4 lock strikers with the 10 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      B0018WGE01
      *1 RH Side:
      *2 LH Side:

  2. INSTALL REAR NO. 6 AIR DUCT

    Click here

  3. INSTALL FRONT FLOOR CARPET ASSEMBLY

    Click here

  4. INSTALL REAR AIR DUCT GUIDE

    Click here

  5. INSTALL AIR DUCT PLUG

    Click here

  6. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

    Click here

  7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Click here

  8. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    Click here

  9. INSTALL REAR NO. 2 SEAT ASSEMBLY

    Click here

  10. INSTALL REAR DOOR SCUFF PLATE LH

    Click here

  11. INSTALL REAR DOOR SCUFF PLATE RH

    Click here

  12. INSTALL REAR STEP COVER

    Click here

  13. INSTALL REAR NO. 2 SEAT PROTECTOR

    B0018RDE01

    1. Attach the 10 claws to install the 2 seat protectors.

  14. INSTALL REAR NO. 1 SEAT PROTECTOR

    B0019HTE01

    1. Attach the 10 claws to install the 2 seat protectors.

  15. INSTALL REAR NO. 1 SEAT ASSEMBLY RH

    Click here

  16. INSTALL REAR NO. 1 SEAT ASSEMBLY LH

    B001B34E02

    1. Temporarily install the seat assembly with the 4 bolts.

      Note

      Be careful not to damage the vehicle body.

    2. Tighten the bolts in the order shown in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
    3. B0018LP

      Connect the connector.

    4. w/ Seat Heater System:

      Connect the connector.

  17. INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER

    B001AKB

    1. Attach the 2 clips and 2 claws to install the cover.

  18. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER

    B001AF7

    1. Attach the 2 clips and 2 claws to install the cover.

  19. INSTALL REAR NO. 5 SEAT CUSHION HINGE COVER


    1. Return the seat to the upright position.

    2. B0019LB

      Attach the 7 claws to install the cover.

  20. INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER

    B00193Q

    1. Attach the 6 claws to install the cover.

  21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  22. CHECK SRS WARNING LIGHT

    Click here

  23. INSPECT REAR NO. 1 SEAT ASSEMBLY LH


    1. w/ Seat Heater System:

      Check the seat heater operation.


      1. Turn the engine switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.