DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Turn Light RH | Turn signal switch (right) status / ON or OFF |
ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
| Turn Light LH | Turn signal switch (left) status / ON or OFF |
ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
| PCS OFF Switch | Pre-crash safety system on/off status / ON or OFF |
ON: Pre-crash safety system on OFF: Pre-crash safety system off |
- |
| Pre-Crash Safety Warning Buz | Pre-crash safety warning buzzer Valid or Inval |
Valid: Pre-crash safety system warning buzzer operation possible Inval: Pre-crash safety system warning buzzer operation not possible |
- |
| Pre-Crash Brake | Pre-crash brake function Valid or Inval |
Valid: Pre-crash brake operation possible Inval: Pre-crash brake operation not possible |
- |
| Pre-Crash safety Warning Buz | Pre-crash safety system warning buzzer / Valid or Inval |
Valid: Pre-crash safety system warning buzzer operation possible Inval: Pre-crash safety system warning buzzer operation not possible |
- |
| Pre-Crash Brake | Pre-crash brake function / Valid or Inval |
Valid: Pre-crash brake operation possible Inval: Pre-crash brake operation not possible |
- |
| PBA Start | Pre-crash brake assist activation signal / OFF, Standby, Assist Lv1 or Assist Lv2 |
OFF: Pre-crash brake assist not operating Standby: Brake pedal not depressed during Pre-crash brake assist operation Assist Lv1: Brake pedal depressed during Pre-crash brake assist operation Assist Lv2: Brake pedal firmly depressed during Pre-crash brake assist operation |
Signal status changes when the Pre-crash brake assist is activated before a collision (Pre-crash brake will activate only in situations where the driver depresses the brake pedal) |
| Warning Brake | - | - | Not applicable to the vehicle |
| Brake Assist Standby | Supplemental brake pressure signal / ON or OFF |
ON: Supplemental brake pressure being provided OFF: Supplemental brake pressure not being provided |
- |
| Pre-Crash Brake Control | Pre-crash brake operational status / ON or OFF |
ON: Pre-crash brake operating OFF: Supplemental brake pressure not being provided |
- |
| AVS Start | - | - | Not applicable to the vehicle |
| VGRS Start | - | - | Not applicable to the vehicle |
| PBA Control | Pre-crash brake assist operational status / Valid or Invalid |
Valid: Pre-crash brake assist control operation possible Invalid: Pre-crash brake assist control operation not possible |
- |
| Pre-Crash Brake Ind | Pre-crash system alarm warning message status / ON or OFF |
ON: Displayed OFF: Not displayed |
"BRAKE!" is displayed |
| PCS Crash Alarm Buzzer | Skid control buzzer status / ON or OFF |
ON: Skid control buzzer sounding OFF: Skid control buzzer not sounding |
- |
| Front Radar-Low Voltage History | Millimeter wave radar sensor assembly low voltage history / ON or OFF |
ON: History of low voltage OFF: No history of low voltage |
- |
| Front Radar-Incorrect Axial Gap (Vertical) History | Millimeter wave radar sensor assembly vertical misalignment history / ON or OFF |
ON: History of vertical misalignment OFF: No history of vertical misalignment |
- |
| Front Radar-Incorrect Axial Gap (Horizontal) History | Millimeter wave radar sensor assembly horizontal misalignment history / ON or OFF |
ON: History of horizontal misalignment OFF: No history of horizontal misalignment |
- |
| Front Recognition Camera-Malfunction History | Forward recognition camera malfunction history (abnormal temperature, low voltage, DTC stored, etc.) / ON or OFF |
ON: History of malfunction OFF: No history of malfunction |
- |
| Control Mode | ECU control mode status / Normal or Check |
Normal: Normal operation Check: Operating in Control Mode |
- |
| PCS Operation State Retention Setting | Displays the setting of the PCS Operation State Retention Setting customize setting / ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 1 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 1 customize setting / ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 2 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 2 customize setting / ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 3 | Displays the setting of the PCS Alarm Activation Distance Retention Setting 3 customize setting / ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
Enter the following menus: Chassis / ABS/VSC/TRAC / Date Test.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch status/ ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Stop Light Relay Output | STPO terminal output condition/ ON or OFF |
ON: Output OFF: Not output |
- |
| EBS Relay | Stop light control relay (Emergency brake signal)/ ON or OFF |
ON: Relay on OFF: Relay off |
- |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus:
for Pre-Crash: Body Electrical / Pre-Crash 2 / Active Test.
for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Active Test.
for Combination Meter: Body Electrical / Combination Meter / Active Test.
Perform Active Test according to the display on the GTS.
Tech Tips
The engine switch must be turned on (IG) to proceed with the Active Test using the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Crash Alarm Buzzer | Skid control buzzer | ON / OFF | Test possible with engine switch on (IG), vehicle stopped |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop lights | ON / OFF | Test possible at vehicle speed of 0 km/h (0 mph) |
| EBS Relay | Stop light control relay (Emergency brake signal) | ON / OFF | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Precrash | PCS OFF warning light | ON / OFF | - |