IMMOBILISER SYSTEM, Diagnostic DTC:B2779

DTC Code DTC Name
B2779 Engine Starter Communication Malfunction

DESCRIPTION

If the remote engine start ECU does not respond to the certification ECU (smart key ECU assembly) or the remote engine start ID is not registered*, this DTC is stored.

If communication between the remote engine start ECU and the certification ECU (smart key ECU assembly) is established and the remote engine start is operated, this DTC and the corresponding history DTC will be cleared.

DTC Code DTC Detection Condition Trouble Area
B2779

One of the following conditions is met (1 trip detection logic*):


  • A remote start communication error occurs.

  • Response is not possible.

  • Registration has not been performed.

  • Remote engine start ECU

  • Main body ECU (multiplex network body ECU)

  • Certification ECU (smart key ECU assembly)

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine does not start with remote start operation Engine cannot be started by remote start operation only
Related Data List and Active Test
DTC Code Data List and Active Test
B2779

  • Wireless Starter Com ID

  • Wireless C Code

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • Before performing the inspection, check that DTC U0142 is not output.

  • Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Service Bulletin.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

PROCEDURE


  1. READ VALUE USING GTS (WIRELESS C CODE)


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Entry&Start / Data List.

    6. Read the Data List according to the display on the GTS.

      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Wireless C Code Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly) / No Regd or Regd

      No Regd: ID not registered between remote engine start ECU and certification ECU (smart key ECU assembly)

      No Regd: ID not registered between remote engine start ECU and certification ECU (smart key ECU assembly)

      Problems may be caused by the following:


      • DTC B2779 is stored.

      • Remote engine start ECU registration has not been performed.

      • Malfunctions in the certification ECU (smart key ECU assembly) or remote engine start ECU.
      Result
      Result Proceed to
      "No Regd" is displayed on the GTS A
      "Regd" is displayed on the GTS B

    B

    CHECK REMOTE ENGINE START ECU Click here

    A

  2. REGISTER REMOTE ENGINE STARTER ID


    1. Register the remote engine starter ID.

      Tech Tips

      Refer to Service Bulletin.


    NEXT

  3. CHECK REMOTE ENGINE STARTER FUNCTION


    1. Check the remote engine starter function.

      OK
      Remote engine starter functions operate normally.

    OK

    END (REMOTE ENGINE STARTER ID REGISTRATION WAS DEFECTIVE)

    NG

  4. CHECK REMOTE ENGINE START ECU


    1. Replace the remote engine starter ECU with a new one.

    2. Register the remote engine starter ID.

      Tech Tips

      Refer to Service Bulletin.

    3. Check the remote engine starter function.

      OK
      Remote engine starter functions operate normally.

    OK

    END (REMOTE ENGINE START ECU WAS DEFECTIVE)

    NG

  5. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    1. Replace the main body ECU (multiplex network body ECU) with a new one.


      Tech Tips

      Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

    2. Check the remote engine starter function.

      OK
      Remote engine starter functions operate normally.

    OK

    END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)