ENTRY AND START SYSTEM(for Start Function) OPERATION CHECK


  1. OPERATION DESCRIPTION

    Note

    Make sure that the entry and start system (for Start Function) has not been canceled before performing this inspection.


    1. Push-button start function:


      1. When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is depressed, the engine is started by pressing the engine switch.

      2. When the electrical key transmitter sub-assembly is in a detection area inside the vehicle and the brake pedal is not depressed, the power source mode is changed by pressing the engine switch. The power source mode changes in the following order every time the engine switch is pressed: off → on (ACC) → on (IG) → off.

      3. B001B2HE01
        Text in Illustration
        *a "ACCESSORY" Display

        After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed while not depressing the brake pedal, the power source mode changes to on (ACC) and "ACCESSORY" is displayed in the combination meter assembly.

      4. B00188VE01
        Text in Illustration
        *a "IGNITION ON" Display

        After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the engine switch is pressed 2 times without depressing the brake pedal, the power source mode changes to on (IG) and "IGNITION ON" is displayed in the combination meter assembly.

      5. After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the engine switch is off, if the brake pedal is depressed while the shift lever is in P or N, the key warning light is displayed in the combination meter assembly.

      6. B00191AE01
        Text in Illustration
        *a Key Warning Light Display

        The engine starts if the engine switch is pressed when the key warning light is displayed.

    2. Changing the power source mode when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:


      1. Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.

      2. While depressing the brake pedal, while facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

      3. B00188VE01
        Text in Illustration
        *a "IGNITION ON" Display

        A buzzer sounds and "IGNITION ON" is displayed in the combination meter assembly, and the power source mode changes to on (IG).

      4. Pressing the engine switch without depressing the brake pedal turns the power source mode from on (IG) to off.

    3. Starting the engine when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:


      1. Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.

      2. While depressing the brake pedal with the shift lever in P or N*, while facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the electrical key transmitter sub-assembly near the engine switch.

        Tech Tips

        *: This is only applicable when the steering wheel is unlocked.

      3. B00191AE01
        Text in Illustration
        *a Key Warning Light Display

        A buzzer in the combination meter assembly will sound, the power source mode changes to on (IG) and the key warning light is displayed in the combination meter assembly.

      4. Press the engine switch with the brake pedal depressed to start the engine.

  2. CHECK PUSH-BUTTON START FUNCTION


    1. Check the push-button start function:


      1. B00191AE01
        Text in Illustration
        *a Key Warning Light Display

        Get into the vehicle while carrying the electrical key transmitter sub-assembly with the engine switch off. With the shift lever in P, check that the key warning light is displayed in the combination meter assembly when the brake pedal is depressed. Then check that the engine starts when the engine switch is pressed after the key warning light is displayed in the combination meter assembly.

      2. While the brake pedal is released and the electrical key transmitter sub-assembly is being carried, check that the power source mode changes in the following order when the engine switch is pressed: off → on (ACC) → on (IG) → off.

        Tech Tips

        When the engine switch is pressed with the engine switch on (IG) and the shift lever not in P, the power source mode does not change to off, but changes to on (ACC).

      3. With the shift lever in P, check that the steering lock operates when a door is opened.

        Tech Tips

        When the engine switch is pressed after the vehicle is stopped, the engine stops and all the power turns off. However, if the shift lever is not in P when the engine switch is pressed with the vehicle stopped, the power source mode does not change to off, but changes to on (ACC).

      4. B001ANFE04
        Text in Illustration
        *a Inspection Point

        Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly in either of the two locations making sure that the electrical key transmitter sub-assembly is oriented as shown in the illustration, and then check that the engine can be started.

        Tech Tips

        Even if the electrical key transmitter sub-assembly is in a vehicle interior key detection area, the electrical key transmitter subassembly may not be properly detected if the electrical key transmitter sub-assembly is on the instrument panel, in a door pocket, in the glove box, on the floor or in a storage compartment.

        Tech Tips


        • If the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever, communication may not be possible.

        • Perform this inspection for both inspection points.

      5. B0019PKE04
        Text in Illustration
        *a Inspection Point

        Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly in either of the two locations making sure that the electrical key transmitter sub-assembly is oriented as shown in the illustration, and then check that the engine can be started.

        Tech Tips

        Even if the electrical key transmitter sub-assembly is in a vehicle interior key detection area, the electrical key transmitter subassembly may not be properly detected if the electrical key transmitter sub-assembly is on the instrument panel, in a door pocket, in the glove box, on the floor or in a storage compartment.

        Tech Tips


        • If the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the rear seat, communication may not be possible.

        • Perform this inspection for both inspection points.

      6. B0019AFE04
        Text in Illustration
        *a Inspection Point

        Check the push-button start function operation range for the luggage side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the engine can be started.

        Tech Tips

        Even if the electrical key transmitter subassembly is in a vehicle interior key detection area, the electrical key transmitter subassembly may not be properly detected if the electrical key transmitter sub-assembly is on the instrument panel, in the glove box or on the floor.

        Tech Tips


        • If the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the rear seat, communication may not be possible.

        • Perform this inspection for both inspection points.

  3. CHECK TRANSMITTER BATTERY SAVING FUNCTION


    1. Check the transmitter battery saving function:


      1. Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.

      2. Check that the entry and start system does not operate while in transmitter battery saving mode.

        Tech Tips

        To cancel transmitter battery saving mode, press a button of the electrical key transmitter sub-assembly.

  4. CHECK POWER SOURCE MODE CHANGING FUNCTION


    1. Check the engine switch.


      1. Check that the power source mode changes according to the chart below.

        Shift Position Brake Pedal Power Source Mode when Engine Switch Pressed
        P Released Off → on (ACC) → on (IG) → off
        P Released Engine running → off
        P Released On (ACC)* → off
        P Depressed Off → engine starts
        P Depressed On (ACC) → engine starts
        P Depressed On (IG) → engine starts
        P Depressed Engine running → off
        P Depressed On (ACC)* → off
        N Released Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed)
        N Released Engine running → on (ACC)
        N Depressed Off → engine starts
        N Depressed On (ACC) → engine starts
        N Depressed On (IG) → engine starts
        N Depressed Engine running → on (ACC)
        Not P or N Released Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed)
        Not P or N Released Engine running → on (ACC)
        Not P or N Depressed Off → on (IG)
        Not P or N Depressed On (ACC) → on (IG)
        Not P or N Depressed Engine running → on (ACC)

        Tech Tips

        *: This situation is only applicable when the power source mode has changed from on (IG) to on (ACC). However, this situation is not applicable when an emergency stop is performed by pressing and holding the engine switch for 2 seconds or more or by quickly pressing the engine switch 3 times or more.

  5. CHECK POWER SOURCE MODE INDICATION


    1. B0018XVE01
      Text in Illustration
      *a "ACCESSORY" Display
      *b "IGNITION ON" Display
      *c Key Warning Light Display

      Check the key warning.

      Multi-information Display Inspection
      Power Source Mode Multi-information Display

      Off

      (Excluding condition in which the engine can be started)

      		 Off

      On (ACC)

      (Excluding condition in which the engine can be started)

      		 "ACCESSORY" display

      On (IG)

      (Excluding condition in which the engine can be started)

      		 "IGNITION ON" display
      Condition in which engine can be started*1 Key warning light display
      Engine started Off

      Tech Tips

      *1: Indicates the condition in which the engine can be started by pressing the engine switch while either of the following conditions is met:


      • Condition 1

        All of the following conditions are met:


        • The power source mode was turned from on (IG) to on (ACC).

        • Key verification is OK*2 or immobiliser is unset (engine switch is on (ACC) or on (IG)).

        • The shift lever is in N and the steering is unlocked.

        • The stop light switch is on.

      • Condition 2

        All of the following conditions are met:


        • The power source mode was not turned from on (IG) to on (ACC).

        • Key verification is OK*2 or immobiliser is unset (engine switch is on (ACC) or on (IG)).

        • The stop light switch is on.

        • The shift lever is in P, or the shift lever is in N with the steering unlocked.

      *2: When the electrical key transmitter sub-assembly is in the cabin, the ID code sent as a result of communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) and the ID code calculated by the certification ECU (smart key ECU assembly) are compared. If the ID codes match each other, the vehicle recognizes that the electrical key transmitter sub-assembly is in the cabin.