LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2325

DTC Code DTC Name
B2325 LIN Communication Bus Malfunction

DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the door and sliding roof. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors and sliding roof is detected consecutively 3 times.

DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between components related to the doors and sliding roof consecutively 3 times.

  • Master switch

  • Front power window regulator motor LH

  • Front power window regulator motor RH

  • Rear power window regulator motor LH

  • Rear power window regulator motor RH

  • Sliding roof ECU

  • Main body ECU (multiplex network body ECU)

  • Harness or connector

WIRING DIAGRAM

A01WQERE02

CAUTION / NOTICE / HINT

Note

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

Tech Tips

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTC Click here.


    NEXT

  2. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)


    1. Disconnect the A ECU connector.

    2. Disconnect the I11*1 or I22*2 switch connector.

    3. Measure the resistance and voltage according to the value(s) in the tables below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - I11-17 (LIN1) Always Below 1 Ω
      A-16 (LIN2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - I22-17 (LIN1) Always Below 1 Ω
      A-16 (LIN2) - Body ground Always 10 kΩ or higher
      Standard Voltage
      Tester Connection Condition Specified Condition
      A-16 (LIN2) - Body ground Always Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CLEAR DTC


    1. Reconnect the A ECU connector.

    2. Disconnect the I11*1 or I22*2 switch connector.

    3. Clear the DTC Click here.

      *1: for LHD

      *2: for RHD


    NEXT

  5. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE MASTER SWITCH Click here

    A

  6. CLEAR DTC


    1. Reconnect the I11*1 or I22*2 switch connector.

      *1: for LHD

      *2: for RHD

    2. Disconnect the I12 motor connector.

    3. Clear the DTC Click here.


    NEXT

  7. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR LH Click here

    A

  8. CLEAR DTC


    1. Reconnect the I12 motor connector.

    2. Disconnect the I4 motor connector.

    3. Clear the DTC Click here.


    NEXT

  9. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR RH Click here

    A

  10. CLEAR DTC


    1. Reconnect the I4 motor connector.

    2. Disconnect the J4 motor connector.

    3. Clear the DTC Click here.


    NEXT

  11. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE REAR POWER WINDOW REGULATOR MOTOR LH Click here

    A

  12. CLEAR DTC


    1. Reconnect the J4 motor connector.

    2. Disconnect the J11 motor connector.

    3. Clear the DTC Click here.


    NEXT

  13. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output A
      DTC B2325 is not output B

    B

    REPLACE REAR POWER WINDOW REGULATOR MOTOR RH Click here

    A

  14. CLEAR DTC


    1. Reconnect the J11 motor connector.

    2. Disconnect the R17 ECU connector.

    3. Clear the DTC Click here.


    NEXT

  15. CHECK FOR DTC


    1. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC B2325 is output (for LHD) A
      DTC B2325 is output (for RHD) B
      DTC B2325 is not output C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here