NAVIGATION SYSTEM, Diagnostic DTC:B15C0, B15C1

DTC Code DTC Name
B15C0 Short in GPS Antenna
B15C1 Open in GPS Antenna

DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly*1 or telephone antenna assembly*2.


DTC Code DTC Detection Condition Trouble Area
B15C0 Navigation antenna error

  • Navigation antenna assembly (w/o heated windshield defroster system)

  • Telephone antenna assembly (w/ heated windshield defroster system)

  • No. 3 antenna cord sub-assembly (w/ heated windshield defroster system)

  • No. 2 antenna cord sub-assembly (w/ heated windshield defroster system)

  • Antenna cord sub-assembly (w/ heated windshield defroster system)

  • Multi-media module receiver assembly
B15C1 Error of the power source to the navigation antenna

WIRING DIAGRAM

A01WVYKE04

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System Click here.

PROCEDURE


  1. CONFIRM MODEL


    1. Choose the model to be inspected.

      Model
      Model Proceed to
      w/o Heated Windshield Defroster System A
      w/ Heated Windshield Defroster System B

    B

    INSPECT TELEPHONE ANTENNA ASSEMBLY Click here

    A

  2. CHECK CONNECTION OF NAVIGATION ANTENNA ASSEMBLY


    1. Check if the navigation antenna assembly is securely connected to the multi-media module receiver assembly.

      OK
      Navigation antenna assembly is securely connected.

    NG

    SECURELY CONNECT NAVIGATION ANTENNA ASSEMBLY

    OK

  3. REPLACE NAVIGATION ANTENNA ASSEMBLY


    1. Replace the navigation antenna assembly with a known good one Click here.


    NEXT

  4. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  5. CHECK DTC


    1. Recheck for DTCs and check if the same DTCs are output again Click here.

      OK
      No DTCs are output.

    OK

    END (NAVIGATION ANTENNA ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

  6. INSPECT TELEPHONE ANTENNA ASSEMBLY


    1. B0019KIE05
      Text in Illustration
      *a Telephone Antenna Assembly

      Remove the telephone antenna assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 2a Always 4 to 11 kΩ

    NG

    REPLACE TELEPHONE ANTENNA ASSEMBLY Click here

    OK

  7. INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. A01WTBCE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Telephone Antenna Assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)

      Disconnect the No. 3 antenna cord sub-assembly from the telephone antenna assembly connector.

    2. Disconnect the No. 3 antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 - B-2 Always Below 1 Ω
      A-2a - B-2a Always Below 1 Ω
      A-2 - Body ground Always 10 kΩ or higher
      A-2a - Body ground Always 10 kΩ or higher

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  8. INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. A01WWETE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 3 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to Antenna Cord Sub-assembly)

      Disconnect the No. 2 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly connector.

    2. Disconnect the No. 2 antenna cord sub-assembly from the antenna cord sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B-2 - C-3 Always Below 1 Ω
      B-2a - C-3a Always Below 1 Ω
      B-2 - Body ground Always 10 kΩ or higher
      B-2a - Body ground Always 10 kΩ or higher

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  9. INSPECT ANTENNA CORD SUB-ASSEMBLY


    1. A01WROXE03
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to Multi-media Module Receiver Assembly)

      Disconnect the antenna cord sub-assembly from the No. 2 antenna cord sub-assembly connector.

    2. Disconnect the antenna cord sub-assembly from the multi-media module receiver assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C-3 - D-1 Always Below 1 Ω
      C-3a - D-1a Always Below 1 Ω
      C-3a - Body ground Always 10 kΩ or higher
      C-3a - Body ground Always 10 kΩ or higher

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  10. REPLACE TELEPHONE ANTENNA ASSEMBLY


    1. Replace the telephone antenna assembly with a known good one Click here.


    NEXT

  11. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  12. CHECK DTC


    1. Recheck for DTCs and check if the same DTCs are output again Click here.

      OK
      No DTCs are output.

    OK

    END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here