STEERING COLUMN ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column Click here.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. FRONT WHEELS FACING STRAIGHT AHEAD

  2. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disable the Autoaway/Return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  5. REMOVE LOWER STEERING COLUMN COVER


    1. B001A0G

      Remove the 3 screws.

    2. B00194WE01
      *1 Push Area

      While pressing the push area shown in the illustration to detach the 2 claws, slightly lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

  6. REMOVE UPPER STEERING COLUMN COVER


    1. B001ACWE03
      *1 Meter Hood Spacer

      Detach the 4 clips and 2 claws and remove the meter hood spacer.

    2. Detach the claw and 2 guide pins and remove the upper steering column cover from the steering column assembly.

  7. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Disconnect the connectors from the combination switch with spiral cable sub-assembly.

    2. B001A1F

      Detach the 3 claws and remove the combination switch assembly with spiral cable sub-assembly from the steering column assembly.

  8. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  9. DISCONNECT WIRE HARNESS PROTECTOR AND WIRE HARNESS


    1. B0018HU

      Detach the 2 claws and 2 harness clamps, disconnect the wire harness protector and wire harness.

  10. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

    Click here

  11. REMOVE STEERING COLUMN ASSEMBLY


    1. B001A23E03
      *1 Matchmark

      Put matchmarks on the steering actuator assembly and the steering column assembly.

    2. Remove the bolt.

    3. B0018Y0

      Remove the 4 nuts and steering column.

  12. REMOVE STEERING ACTUATOR ASSEMBLY

    Click here

  13. REMOVE STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    1. B0019S9

      Remove the 4 bolts, nut and steering column hole cover.

  14. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT


    1. B001994E02
      *1 Matchmark

      Loosen the bolt and remove the No. 2 intermediate shaft from the power steering link assembly.

      Note

      It is possible to install the intermediate shaft to the same position it was removed from without placing matchmarks due to the dust cover part labeled A. Therefore, do not remove the dust cover from the steering link.

      Tech Tips

      If the dust cover is removed/installed or replaced, place matchmarks on the dust cover and steering link.