VANE PUMP(for 1VD-FTV) ON-VEHICLE INSPECTION

PROCEDURE


  1. CHECK STEERING EFFORT

    CAUTION:

    These service operations may affect the SRS airbags. Be sure to read the precautionary notices concerning the SRS airbag system before servicing.

    Click here


    1. Stop the vehicle on a level, paved surface and align the wheels straight ahead.

    2. Remove the steering pad assembly.

      Click here

    3. Connect the cable to the negative (-) battery terminal.

    4. Using a torque wrench, check that the steering wheel set nut is properly tightened.

      Click here

    5. Start the engine so that the power steering is ready to operate.

    6. Turn the steering wheel 90 degrees to the right and check the steering effort (torque) while continuing to turn it further in the same direction.

      Standard steering effort (Reference):
      6.0 N*m (61 kgf*cm, 53 in.*lbf) or less

    7. Align the front wheels facing straight ahead.

    8. Turn the engine switch off.

    9. Disconnect the cable from the negative (-) battery terminal.

    10. Install the steering pad assembly.

      Click here

  2. BLEED POWER STEERING SYSTEM


    1. Check the fluid level.

    2. Jack up the front of the vehicle and support it with stands.

    3. Turn the steering wheel.


      1. With the engine stopped, turn the wheel slowly from lock to lock several times.

    4. Lower the vehicle.

    5. Start the engine.

    6. Idle the engine for a few minutes.

    7. Turn the steering wheel.


      1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds. *1

      2. Repeat *1 several times.

        Note

        For vehicles with VGRS, if the steering wheel is turned from lock to lock repeatedly, the system may stop operating and the amount of rotation before the steering wheel locks may increase due to operation of the overheating prevention function. When the system temperature drops, the system operation automatically returns to normal.

    8. Stop the engine.

    9. A01WPS8E03
      Text in Illustration
      *a Correct
      *b Incorrect

      Check for foaming or emulsification.

      If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

    10. Check the fluid level.

  3. CHECK FLUID LEVEL


    1. A01WT3UE05
      Text in Illustration
      *a COLD Range
      *b HOT Range

      Keep the vehicle horizontal.

    2. With the engine stopped, check the fluid level in the reservoir.

      If necessary, add fluid.

      Fluid
      ATF DEXRON II or III, or equivalent

      Tech Tips

      If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.

    3. Start the engine and idle it.

    4. Turn the steering wheel from lock to lock several times to raise the fluid temperature.

      Fluid temperature
      80°C (176°F)
    5. A01WPS8E03
      Text in Illustration
      *a Correct
      *b Incorrect

      Check for foaming or emulsification.

      If foaming or emulsification is identified, bleed the power steering system.

    6. A01WW46E01
      Text in Illustration
      *a Engine idling
      *b Engine stopped
      *c 5.0 mm (0.197 in.) or less

      With the engine idling, measure the fluid level in the reservoir.

    7. Stop the engine.

    8. Wait a few minutes and remeasure the fluid level in the reservoir.

      Maximum fluid level rise
      5.0 mm (0.197 in.)

      If the fluid level rise is more than the maximum, bleed the power steering system.

    9. Check the fluid level.

  4. CHECK STEERING FLUID PRESSURE


    1. Disconnect the pressure feed tube from the vane pump.

      Click here

    2. Connect SST as shown in the illustration.

      SST
      09640-10011   ( 09641-01010, 09641-01040, 09641-01070, 09641-01030 )
      A01WSJ7E04
      Text in Illustration
      *A w/o Variable Flow Control Solenoid Valve *B w/ Variable Flow Control Solenoid Valve
      *1 Attachment *2 Pressure Feed Tube
      *a IN *b OUT

      Note

      Make sure that the valve of SST is in the open position.

    3. Bleed the power steering system.

    4. Start the engine and idle it.

    5. Turn the steering wheel from lock to lock several times to raise the fluid temperature.

      Fluid temperature
      80°C (176°F)
    6. A01WVO7E02
      Text in Illustration
      *1 Power Steering Gear
      *2 Oil Reservoir
      *3 Vane Pump
      *a Closed

      With the engine idling, close the valve of SST and observe the reading on SST.

      Standard Fluid Pressure
      except Middle East

      10000 to 10700 kPa (102 to 109 kgf/cm2, 1450 to 1551 psi)
      for Middle East

      11500 to 12500 kPa (118 to 127 kgf/cm2, 1668 to 1812 psi)

      Note


      • Do not keep the valve closed for more than 10 seconds.

      • Do not allow the fluid temperature to become too high.

      If the pressure is less than the minimum, check for fluid leaks and replace parts as necessary.

    7. A01WT26E02
      Text in Illustration
      *1 Power Steering Gear
      *2 Oil Reservoir
      *3 Vane Pump
      *a Open

      With the engine idling, fully open the valve.

    8. Measure the fluid pressure at engine speeds of 1000 rpm and 3000 rpm.

      Difference in fluid pressure
      500 kPa (5.1 kgf/cm2, 73 psi) or less

      Note

      Do not turn the steering wheel.

      If the pressure difference is higher than the specified value, check for fluid leaks and replace parts as necessary.

    9. A01WQG9E02
      Text in Illustration
      *1 Power Steering Gear
      *2 Oil Reservoir
      *3 Vane Pump
      *a Open
      *b Lock Position

      With the engine idling and the valve fully open, turn the steering wheel left or right to the full lock position. Observe the reading on SST.

      Standard Fluid Pressure
      except Middle East

      10000 to 10700 kPa (102 to 109 kgf/cm2, 1450 to 1551 psi)
      for Middle East

      11500 to 12500 kPa (118 to 127 kgf/cm2, 1668 to 1812 psi)

      Note


      • Do not keep the steering wheel in the full lock position for more than 10 seconds.

      • Do not allow the fluid temperature to become too high.

      If the pressure is less than the minimum, check for fluid leaks and replace parts as necessary.

    10. Disconnect SST.

    11. Connect the pressure feed tube to the vane pump.

      Click here

    12. Bleed the power steering system.