OIL COOLER INSTALLATION

PROCEDURE


  1. INSTALL OIL COOLER ASSEMBLY


    1. B001902E05
      Text in Illustration
      *1 Air Cooled Oil Cooler Tube
      *2 Oil Cooler Inlet Hose
      *3 Oil Cooler Outlet Hose
      *a Lower Side
      *b Vehicle Rear Side
      *c 0 to 3 mm (0 to 0.118 in.)
      *d 2 to 7 mm (0.079 to 0.275 in.)
      *e Matchmarks

      Install the oil cooler inlet hose to the oil cooler assembly, and slide the clip to secure the hose as shown in the illustration.

    2. Install the oil cooler outlet hose to the oil cooler assembly, and slide the clip to secure the hose as shown in the illustration.

    3. Install the air cooled oil cooler tube to the oil cooler outlet hose and oil cooler inlet hose, and slide the 2 clips to secure the hoses as shown in the illustration.

    4. B0018AH

      Install the rear transmission oil cooler air duct with the 4 bolts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

    5. Connect the air cooled oil cooler tube to the transmission oil cooler air duct with the bolt.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }
    6. B00190GE05
      Text in Illustration
      *a Claw

      Temporarily put the oil cooler assembly on the radiator support.

      Note

      Securely attach the 2 claws of the oil cooler assembly into the holes of the radiator support.

    7. Install the 4 bolts in the sequence shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  2. INSTALL TRANSMISSION OIL COOLER AIR DUCT (except Sport Package)


    1. Install the transmission oil cooler air duct with the 4 bolts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

  3. INSTALL OIL COOLER TUBE


    1. B0019LOE05

      Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL INLET NO. 4 OIL COOLER HOSE


    1. B0019H5E03
      Text in Illustration
      *a Paint Mark
      *b 2 to 7 mm (0.079 to 0.275 in.)
      *c 0 to 3 mm (0 to 0.118 in.)

      Install the inlet No. 4 oil cooler hose and slide the 2 clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

  5. INSTALL INLET NO. 2 OIL COOLER HOSE


    1. B001B2CE03
      Text in Illustration
      *1 Inlet No. 2 Oil Cooler Hose
      *2 Inlet No. 3 Oil Cooler Hose
      *a 2 to 7 mm (0.079 to 0.275 in.)
      *b 0 to 3 mm (0 to 0.118 in.)

      Install the inlet No. 2 oil cooler hose and slide the 2 clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  6. INSTALL INLET NO. 3 OIL COOLER HOSE


    1. Install the inlet No. 3 oil cooler hose and slide the 2 clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  7. INSTALL OUTLET NO. 1 OIL COOLER HOSE


    1. B001B2JE05
      Text in Illustration
      *1 Outlet No. 1 Oil Cooler Hose
      *2 Inlet No. 1 Oil Cooler Hose
      *a 2 to 7 mm (0.079 to 0.275 in.)
      *b 0 to 3 mm (0 to 0.118 in.)
      *c Matchmark

      Connect the outlet No. 1 oil cooler hose and slide the 2 clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

    2. Attach the hose to the flexible hose clamp and close the clamp as shown in the illustration.

  8. INSTALL INLET NO. 1 OIL COOLER HOSE


    1. Connect the inlet No. 1 oil cooler hose and slide the 2 clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

  9. ADD AUTOMATIC TRANSMISSION FLUID

    Click here

  10. INSTALL FRONT UPPER CENTER BUMPER RETAINER

    Click here

  11. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


    1. Start the engine. Make sure that there are no automatic transmission fluid leaks from the areas that were worked on.

  12. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  13. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

    Click here

  15. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

    Click here

  16. INSTALL FRONT FENDER APRON SEAL REAR RH

    Click here

  17. INSTALL FRONT FENDER APRON SEAL FRONT RH

    Click here