FUEL PUMP INSTALLATION

PROCEDURE


  1. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    1. Apply a light coat of gasoline or grease to a new gasket, and install it to the fuel tank.

    2. A01WU7KC04
      *a Protrusion
      *b Groove
      B0018FC Front

      Install the fuel suction with pump and gauge tube into the fuel tank.

      Note

      Be careful not to bend the arm of the fuel sender gauge.

      Tech Tips

      Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.

    3. A01WRS0C01
      *a Co-rotation Prevention Check Mark
      B0018FC Front

      Apply a co-rotation prevention check mark to the fuel tank vent tube assembly.

      Tech Tips

      Perform this procedure when replacement of the fuel tank vent tube assembly is necessary.

    4. A01WPKQC01
      *a Rotational Start Point Mark (Fuel Tank Assembly Side)
      *b Rotational Start Point Mark (Fuel Pump Gauge Retainer Side)
      B0018FC Front

      Temporarily place the fuel pump gauge retainer by aligning the rotational start point mark of a new fuel pump gauge retainer with the rotational start point mark of the fuel tank assembly while pressing the fuel tank vent tube assembly into the fuel tank assembly.

    5. A01WPERC01
      *1 Fuel Pump Gauge Retainer
      *a SST (Claw Set)
      *b Rib
      *c Cutout
      *d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)

      Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

      SST
      09808-14031   ( 09808-01080, 09808-01090, 09808-01100 )

      Note


      • Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

      • Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.

    6. A01WQ3DC03
      *1 Fuel Pump Gauge Retainer
      *a SST (Claw Set)
      *b Hook
      B0018FC Press
      B00199O SST (Bolt)

      While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.

    7. A01WPL6C01
      *a SST (Plate)
      *b SST (Claw Set)
      B0018FC SST (Bolt)

      Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).

    8. A01WUC6C01
      *a Center of Fuel Pump Gauge Retainer
      *b SST (Plate)
      B0018FC Front

      Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.

    9. A01WWTCC01
      *1 Fuel Pump Gauge Retainer
      *a SST (Plate)
      *b SST (Claw Set)
      *c SST (Bolt)
      *d Rib
      B0019R3 Press

      While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).

    10. A01WWYLC01
      *a Co-rotation Prevention Check Mark
      *b Tightening Start Position
      *c One and Half Rotation Position
      B0018FC Front

      While one person presses the fuel tank vent tube assembly into the fuel tank assembly, have another person firmly press the fuel pump gauge retainer into the threads of the fuel tank assembly and tighten approximately one and a half turns.

      Note


      • Do not use any tools other than SST, such as a screwdriver, etc.

      • Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

      • Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.

      • Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.

    11. A01WWB4C01
      *a SST (Plate)
      *b Person in Charge of Tightening
      *c Person in Charge of Supporting
      *d Approximately 180°
      B0018FC Front

      While one person presses the fuel tank vent tube assembly into the fuel tank assembly, have another person slowly tighten approximately 180°.

    12. Check the tightening condition of the fuel pump gauge retainer.


      1. A01WQBNC01
        *1 Fuel Pump Gauge Retainer
        *2 Fuel Tank Assembly
        *a Vernier Caliper
        *b Measurement Height
        B00199O Front
        B0019ZQ Measurement Position

        Using a vernier caliper, measure the upper surface dimensions of the fuel tank assembly at the 3 positions as shown in the illustration.

        Standard
        Measurement difference is within 3 mm.

        Note

        If the measurement difference is approximately 6 mm, the threads misaligned by 1 threads (6 mm) and the fuel pump gauge retainer must be installed again.

    13. Install SST (handle) to SST (plate).

      SST
      09808-14031   ( 09808-01010, 09808-01020 )
    14. A01WTDGC01
      *a SST (Handle)
      *b SST (Plate)
      *c Tightening Complete Position
      *d Rotational Start Point Mark of Fuel Pump Gauge Retainer
      *e Rotational Start Point Mark of Fuel Tank Assembly
      *f Person in Charge of Tightening
      *g Person in Charge of Supporting
      B0018FC Tighten
      B00199O Front

      While one person presses the fuel tank vent tube assembly onto the fuel tank assembly, have another person use SST (handle) and slowly tighten the fuel pump gauge retainer until it reaches the tightening complete position.

  2. INSTALL FUEL TANK SUB-ASSEMBLY

    Click here