FOG LIGHT ASSEMBLY DISASSEMBLY

CAUTION / NOTICE / HINT

Note


  • Be sure to read Precaution thoroughly before servicing Click here.

  • Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

  • Do not reuse parts which have reduced fastening ability due to thread damage.

  • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

  • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

  • When installing components, make sure that the wire harness is not pinched or pulled.

  • Do not use solvent to clean components. Only clean them with a dry cloth.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE FOG LIGHT BRACKET LH


    1. B001B31

      Remove the 2 screws.

    2. Using a screwdriver, detach the claw and remove the fog light bracket LH.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      B0019VB Protective Tape

  2. REMOVE FOG LIGHT LENS LH

    Note


    • Perform work using clean rubber gloves.

    • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.


    1. B001AP6E01

      Remove the 6 screws.

    2. Using a T20H "TORX" driver, remove the "TORX" screw.

      Text in Illustration
      *a "TORX" Screw
    3. B001AUS

      Detach the 6 claws.

    4. B001AQWE01
      Text in Illustration
      *a Separation Starting Point

      Using a dryer, warm the fog light seal from the backside of the fog light assembly LH at the separation starting point of the fog light seal and fog light housing.

    5. With the fog light lens LH slightly lifted, cut the fog light seal with scissors and remove the fog light lens LH.

      Tech Tips


      • If the fog light lens LH cannot be removed even after heating, using a screwdriver, lift the fog light lens LH.

      • Tape the screwdriver tip before use.

  3. REMOVE FOG LIGHT SEAL

    Note


    • The seal must not be reused.

    • Perform work using clean rubber gloves.

    • Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.


    1. B0018K5

      Remove the fog light seal from the fog light housing.

      Text in Illustration
      B0019VB Fog Light Seal

  4. REMOVE CORNERING LIGHT UNIT LH (w/ Cornering Light)

    Note


    • Perform work using clean rubber gloves.

    • Do not touch the cornering light unit LH with bare hands.

    • Do not touch the metallic surfaces as much as possible, or they may become dirty.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.


    1. B00188I

      Disconnect the connector.

    2. B0018QL

      Remove the 3 screws and cornering light unit LH.

    3. B0019XG

      Disconnect the connector.

    4. B001910

      Remove the screw and circuit sub-assembly.

  5. REMOVE FOG LIGHT UNIT LH

    Note


    • Perform work using clean rubber gloves.

    • Do not touch the cornering light unit LH with bare hands.

    • Do not touch the metallic surfaces as much as possible, or they may become dirty.

    • Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

    • Do not use solvent to clean components. Only clean them with a dry cloth.


    1. B0019FBE02
      Text in Illustration
      *a Protrusion Amount Measurement Area

      Using a vernier caliper, measure and record the protrusion amount of the aiming screw.

    2. B001B3A

      Disconnect the connector.

    3. B001AE8

      Tighten the aiming screw 20 rotations.

    4. B001B57

      Using a clip remover, disconnect the 2 pivot collars

      Tech Tips

      Tape the clip remover tip before use.

      Text in Illustration
      B0019VB Protective Tape

    5. While holding the fog light unit LH with one hand so that it does not fall over, loosen the aiming screw until the fog light unit LH is removed.

      Tech Tips

      Count and record the number of rotations before the fog light unit LH is removed.

  6. REMOVE LIGHT CONTROL LED ECU


    1. B0018RN

      Disconnect the connector.

    2. Remove the 2 screws and light control LED ECU.

  7. REMOVE FOG LIGHT CORD


    1. B00196E

      Remove the screw and disconnect the bracket.

    2. Disconnect the grommet and pull out the fog light cord to remove it.