ADAPTIVE HIGH BEAM SYSTEM FREEZE FRAME DATA


  1. FREEZE FRAME DATA


    1. Whenever an adaptive high beam system DTC is stored, the headlight ECU sub-assembly LH stores the current vehicle state as freeze frame data.

  2. CHECK FREEZE FRAME DATA


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / AFS / Trouble Codes.

    5. Select a DTC to display its freeze frame data.

      AFS
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      AHS Switch Integration control and panel assembly (adaptive high beam switch) signal / ON or OFF

      ON: Integration control and panel assembly (adaptive high beam switch) is operated

      OFF: Integration control and panel assembly (adaptive high beam switch) is not operated

      		 -
      Traveling Direction Traveling direction / Not Fwd or Fwd

      Not Fwd: Shift lever in R or N

      Fwd: Shift lever not in R or N

      		 -
      Headlight Low Beam State Low beam headlight state / ON or OFF

      ON: Low beam headlights on

      OFF: Low beam headlights off

      		 -
      Headlight High Beam State High beam headlight state / ON or OFF

      ON: High beam headlights on

      OFF: High beam headlights off

      		 -
      DRL State Daytime running light state / ON or OFF

      ON: Daytime running lights on

      OFF: Daytime running lights off

      		 -
      Clearance Light State Clearance light state / ON or OFF

      ON: Clearance lights on

      OFF: Clearance lights off

      		 -
      Right Cornering Light State Cornering light RH state / ON or OFF

      ON: Cornering light RH on

      OFF: Cornering light RH off

      		 -
      Left Cornering Light State Cornering light LH state / ON or OFF

      ON: Cornering light LH on

      OFF: Cornering light LH off

      		 -
      Engine Engine condition / Run or Stop

      Run: Engine is running

      Stop: Engine is stoped

      		 -
      Passing Light Switch Dimmer switch high flash position (pass) signal / ON or OFF

      ON: Dimmer switch in high flash position

      OFF: Dimmer switch not in high flash position

      		 -
      AHS Operation Condition Status of adaptive high beam system operation conditions / Failure or Approval

      Failure: Adaptive high beam system operation conditions not met

      Approval: Adaptive high beam system operation conditions met

      		 -
      Optical Axis Control State Leveling motor beam axis control during high-speed driving status / ON or OFF

      ON: Leveling motor beam axis control performed during high-speed driving

      OFF: Leveling motor beam axis control not performed during high-speed driving

      		 -
      Steering Sens Signal Steering angle sensor signal value / -384.0 deg to 382.5 deg 0.0 deg -
      FR Wheel Speed Front right wheel speed / 0.00 to 260.00 km/h (162.00 mph) Vehicle stopped: 0 km/h (0 mph) -
      FL Wheel Speed Front left wheel speed / 0.00 to 260.00 km/h (162.00 mph) Vehicle stopped: 0 km/h (0 mph) -
      Vehicle Acceleration

      Vehicle acceleration / -455.64 to 445.60 m/s2

      Vehicle stopped: 0.0 m/s2

      		-
      Leveling Motor Slave Status of the headlight leveling motor slave / Normal or Abnormal

      Normal: Headlight leveling motor is normal

      Abnormal: Headlight leveling motor is not normal

      		 When Abnormal, LIN communication may be lost.
      Leveling Motor Over- Run Status of the headlight leveling motor over-run / Normal or Abnormal

      Normal: Headlight leveling motor is normal

      Abnormal: Headlight leveling motor is not normal

      		 When Abnormal, LIN communication may be lost.
      AHS EDU Slave Status of the headlight light control ECU sub-assembly slave / Normal or Abnormal

      Normal: headlight light control ECU sub-assembly is normal

      Abnormal: headlight light control ECU sub-assembly is not normal

      		 When Abnormal, LIN communication may be lost.
      AHS EDU Over-Run Status of the headlight light control ECU sub-assembly over-run / Normal or Abnormal

      Normal: headlight light control ECU sub-assembly is normal

      Abnormal: headlight light control ECU sub-assembly is not normal

      		 When Abnormal, LIN communication may be lost.
      +B Headlight ECU sub-assembly LH IG power supply voltage value / 0 to 19.75 V 11.00 to 14.00 V -
      +B Voltage Value Headlight ECU sub-assembly LH +B power supply voltage value / 0 to 19.75 V 11.00 to 14.00 V -
      Number Of Trouble Codes Number of stored DTCs when Freeze Frame Data stored / 0 to 255 0 to 255 -

  3. CLEAR FREEZE FRAME DATA

    Note

    Clearing the DTCs will also clear the freeze frame data.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Clear the DTCs and freeze frame data Click here.