REAR SEAT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL BENCH TYPE REAR SEATBACK COVER


    1. Using hog ring pliers, install the bench type rear seatback cover to the bench type rear seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A000OCME01
      Text in Illustration
      *1 Hog Ring Pliers - -

    2. w/ Rear Seat Side Airbag:


      1. A000P26

        Pass the brackets of the bench type rear seatback cover through the holes in the bench type rear seatback pad.

        Note


        • After the bench type rear seatback cover is installed, make sure the bench type rear seatback cover bracket is not twisted.

      2. Install the rear seat airbag assembly LH Click here.

      3. Install the rear seat airbag assembly RH.

        Tech Tips

        Use the same procedure described for the LH side.

    3. A000NO2

      w/ Seat Heater System:

      Pass the rear seatback heater wire harnesses through the holes in the bench type rear seatback cover.

    4. Pass the bench type rear seatback pad through the holes in the bench type rear seatback cover.

    5. Pass the bench type rear seatback cover through the holes in the bench type rear seatback pad.

    6. Using hog ring pliers, install the bench type rear seatback cover to the bench type rear seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A000N96E01
      Text in Illustration
      *1 Hog Ring Pliers - -

  2. INSTALL REAR SEAT HEADREST SUPPORT


    1. Attach the 12 claws to install the 6 rear seat headrest supports.

    2. A000R2YE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the bench type rear seatback cover to the bench type rear seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  3. INSTALL REAR SEAT CENTER SHOULDER BELT GUIDE


    1. Install the rear seat center shoulder belt guide with the 2 screws.

  4. INSTALL REAR SEAT SHOULDER BELT GUIDE RH


    1. Install the rear seat shoulder belt guide RH with the 3 screws.

  5. INSTALL REAR SEAT SHOULDER BELT GUIDE LH

    Tech Tips

    Use the same procedure described for the RH side.

  6. INSTALL REAR SEAT WIRE RH (for Luxury Seat Type)


    1. A000SGL

      w/o Seat Heater System:

      Attach the claw and 2 clamps to install the rear seat wire RH.

    2. A000T7J

      w/ Seat Heater System:


      1. Attach the claw and 3 clamps to install the rear seat wire RH.

      2. Pass the rear seat wire RH under the rubber bands of the bench type rear seatback cover.

      3. Connect the 2 rear seatback heater connectors.

  7. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

    Click here

  8. INSTALL REAR SEAT CENTER ARMREST BOX (for Luxury Seat Type)


    1. Install the rear seat center armrest box to the rear seat center armrest pad.

    2. Attach the 30 hooks to install the rear seat center armrest cover sub-assembly.

  9. INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY


    1. Install the rear seat center armrest cup holder sub-assembly with the 2 screws.

  10. INSTALL REAR CONSOLE BOX WIRE (for Luxury Seat Type)


    1. A000NQL

      Attach the 3 clamps to install the rear console box wire.

  11. INSTALL REAR CONTROL SWITCH (for Luxury Seat Type)


    1. Attach the 4 claws to install the rear control switch.

  12. INSTALL REAR SEAT CENTER ARMREST BOX ASSEMBLY


    1. Attach the 4 claws to install the rear seat center armrest box assembly.

  13. INSTALL REAR SEAT CENTER ARMREST PANEL SUB-ASSEMBLY


    1. for Luxury Seat Type:

      Connect the rear console box wire connector.

    2. Attach the 3 guides and 6 claws.

    3. Install the rear seat center armrest panel sub-assembly with the screw.

  14. INSTALL ARMREST CONSOLE HINGE SUB-ASSEMBLY


    1. Install the armrest console hinge sub-assembly with the 2 screws.

  15. INSTALL CENTER ARMREST LOCK SUB-ASSEMBLY


    1. Install the center armrest lock sub-assembly with the 4 screws.

  16. INSTALL REAR NO. 1 SEAT CENTER ARMREST PLATE


    1. Install the rear No. 1 seat center armrest plate with the 4 screws.

  17. INSTALL REAR SEAT CENTER ARMREST DOOR SUB-ASSEMBLY


    1. Attach the claw to install the rear seat center armrest door sub-assembly with the 2 screws.

  18. INSTALL NO. 1 SEAT ARMREST CAP


    1. Attach the 4 guides and 4 claws to install the No. 1 seat armrest cap.

  19. INSTALL CUSHION


    1. Install the 2 cushions to the rear seat armrest hole board sub-assembly.

  20. INSTALL REAR SEAT HOOK (for Luxury Seat Type)


    1. Install the rear seat hook with the screw.

  21. INSTALL REAR SEAT ARMREST HOLE BOARD SUB-ASSEMBLY


    1. Install the 2 clips.

    2. Attach the 2 hooks to install the rear seat armrest hole board sub-assembly.

    3. A000NJI

      for Luxury Seat Type:

      Attach the clamp of the rear console box wire.

  22. INSTALL REAR SEAT CENTER ARMREST HINGE


    1. Install the rear seat center armrest hinge and 2 bushes with the 2 screws.

  23. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    1. A000RHL

      for Luxury Seat Type:

      Position the rear console box wire as shown in the illustration.

    2. A000P54

      Move the rear seat center armrest assembly in the direction of the arrow to attach the 2 hooks.

    3. Install the rear seat center armrest assembly with the 2 nuts.

    4. for Luxury Seat Type:


      1. A000PAO

        w/o Seat Heater System:

        Connect the connector and attach the clamp of the rear console box wire.

      2. A000T4K

        w/ Seat Heater System:

        Connect the connector, attach the clamp of the rear console box wire and attach the 3 clamps of the rear seat wire RH.

  24. INSTALL BENCH TYPE REAR SEAT CUSHION COVER


    1. Using hog ring pliers, install the bench type rear seat cushion cover to the rear seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A000RIXE01
      Text in Illustration
      *1 Hog Ring Pliers - -
    2. A000O3R

      w/ Seat Heater System:

      Pass the rear seat cushion heater wire harnesses through the holes in the bench type rear seat cushion cover.

    3. A000PN5

      Pass the rear seat cushion pad through the holes in the bench type rear seat cushion cover.

    4. Pass the bench type rear seat cushion cover through the holes in the rear seat cushion pad.

    5. Using hog ring pliers, install the bench type rear seat cushion cover to the rear seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

      A000RP4E01
      Text in Illustration
      *1 Hog Ring Pliers - -