FRONT SEAT ASSEMBLY(for Standard Seat Type) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH

    Click here

  2. INSTALL SEATBACK FELT


    1. Install a new seatback felt.

  3. INSTALL FRONT SEAT WIRE

    A000PU9

    1. Attach the 9 wire harness clamps to install the front seat wire.

    2. Connect the 3 connectors.

    3. Attach the 4 wire harness clamps.

  4. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    A000OVBE03
    Text in Illustration
    *1 Wire Harness Clamp
    *2 Hook A
    *3 Hook B

    1. Attach the 4 hooks B to install the separate type front seat cushion spring assembly.

    2. Attach the 4 hooks A.

    3. Attach the 3 wire harness clamps.

  5. INSTALL SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)

    Click here

  6. INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

    Click here

  7. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

    Click here

  8. INSTALL RECLINING ADJUSTER INSIDE COVER LH

    Click here

  9. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. INSTALL FRONT NO. 2 SEATBACK WIRE SET BRACKET


    1. Install the front No. 2 seatback wire set bracket with the nut.

  11. INSTALL FRONT NO. 1 SEATBACK WIRE SET BRACKET


    1. Install the front No. 1 seatback wire set bracket with the nut.

  12. INSTALL RECLINING ADJUSTER INSIDE COVER

    Click here

  13. INSTALL POWER SEAT MOTOR ASSEMBLY

    Click here

  14. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  15. INSTALL FRONT SEAT BRACKET LH


    1. Install the front seat bracket LH with the nut.

  16. INSTALL FRONT SEATBACK INSIDE SPRING SET PLATE LH

    A000NNP

    1. Install the front seatback inside spring set plate LH to the front seat bracket LH.

  17. INSTALL FRONT SEAT BRACKET RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. INSTALL FRONT SEATBACK INSIDE SPRING SET PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Click here

  20. INSTALL REAR AIR DUCT LH (w/ Climate Control Seat System)

    Click here

  21. INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)


    1. Attach the hook to install the seatback climate control blower LH together with the rear air duct LH.

    2. Install the 2 screws.

    3. Attach the 2 claws to connect the rear air duct LH to the lumbar support adjuster LH.

    4. Connect the connector.

  22. INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY

    Click here

  23. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A000O06E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A000QIE

      Pass the 2 seatback cover brackets through the 2 holes of the separate type front seatback pad.

  24. INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. A000P2RE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the 2 seatback cover brackets with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:

      After the seatback cover bracket is attached, make sure the seatback cover bracket is not twisted.

    3. Attach the wire harness clamp.

    4. Attach the 4 claws to install the 2 front seat headrest supports.

    5. Attach the hooks.

  25. INSTALL SEAT CUSHION SPRING DAMPER

    Click here

  26. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A000P21E01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A000OL6E01
      Text in Illustration
      *1 Strap
      *2 Hog Ring Pliers

      Using hog ring pliers, connect the 3 straps to the separate type front seat cushion pad with new hog rings.

      Note

      Be careful not to damage the cover.

  27. INSTALL SEAT CUSHION COVER WITH PAD


    1. Set the seat cushion cover with pad in place.

    2. Attach the hooks to install the seat cushion cover with pad.

    3. for Front Passenger Side:

      Connect the connector.

    4. Install the 4 clips.

    5. w/ Seat Heater System:


      1. Connect the connector and install the connector lock to the seat heater control sub-assembly LH connector.

      2. Connect the 2 connectors.

  28. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

    Click here

  29. INSTALL FRONT SEAT LEG COVER LH

    Click here

  30. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A000QDP

    1. Slide the front seatback board sub-assembly LH upward to attach the 2 hooks and install it.

    2. Attach the 2 claws.

    3. Open the lower part of the front seatback board sub-assembly LH and install the 2 screws.

    4. Install the clip.

    5. Attach the hook to connect the rubber band.

    6. Connect the rubber band with the clip.

  31. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  32. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  33. INSTALL UPPER SEAT TRACK RAIL COVER LH

    Click here

  34. INSTALL FRONT LUMBAR POWER SEAT SWITCH

    Click here

  35. INSTALL POWER SEAT SWITCH ASSEMBLY

    Click here

  36. INSTALL FRONT POWER ADJUSTER SHIELD LH


    1. Install 2 new clips to the front power adjuster shield LH.

    2. Install the switch bezel to the front power adjuster shield LH with the 4 screws.

    3. for Driver Side:

      Connect the 3 connectors.

    4. for Front Passenger Side:

      Connect the 2 connectors.

    5. Attach the 2 clips to install the front power adjuster shield LH.

    6. Install the 2 screws.

  37. INSTALL POWER SEAT SWITCH KNOB LH (for Reclining)

    Click here

  38. INSTALL POWER SEAT SWITCH KNOB LH (for Slide)

    Click here

  39. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    Click here

  40. INSTALL FRONT SEAT CUSHION SHIELD LH

    Click here

  41. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH


    1. Attach the 2 clips and 2 claws to install the front seat inner No. 1 cushion shield LH.

    2. Install the screw.

  42. INSTALL SEAT ADJUSTER COVER CAP LH

    Click here