FRONT SEAT ASSEMBLY(for Standard Seat Type) DISASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE SEAT ADJUSTER COVER CAP LH

    Click here

  2. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD LH

    A000MU5

    1. Remove the screw.

    2. Detach the 2 claws and 2 clips and remove the front seat inner No. 1 cushion shield LH.

  3. REMOVE FRONT SEAT CUSHION SHIELD LH

    Click here

  4. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

    Click here

  5. REMOVE POWER SEAT SWITCH KNOB LH (for Slide)

    Click here

  6. REMOVE POWER SEAT SWITCH KNOB LH (for Reclining)

    Click here

  7. REMOVE FRONT POWER ADJUSTER SHIELD LH

    A000RVN

    1. Remove the 2 screws.

    2. Detach the 2 clips and remove the front power adjuster shield LH.

    3. A000NKJ

      for Driver Side:

      Disconnect the 3 connectors.

    4. A000Q4N

      for Front Passenger Side:

      Disconnect the 2 connectors.

    5. A000P6P

      Remove the 4 screws and switch bezel from the front power adjuster shield LH.

    6. A000P4Y

      Remove the 2 clips from the front power adjuster shield LH.

  8. REMOVE POWER SEAT SWITCH ASSEMBLY

    Click here

  9. REMOVE FRONT LUMBAR POWER SEAT SWITCH

    Click here

  10. REMOVE UPPER SEAT TRACK RAIL COVER LH

    Click here

  11. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  12. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  13. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A000O6K

    1. Using a clip remover, remove the clip and disconnect the rubber band.

    2. Detach the hook and disconnect the rubber band.

    3. Using a clip remover, remove the clip.

    4. A000QN4

      Open the lower part of the front seatback board sub-assembly LH and remove the 2 screws.

    5. Push and slide the front seatback board subassembly LH to detach the claw.

      Tech Tips

      Use the same procedure to detach the claw on the other side.

    6. Slide the front seatback board sub-assembly LH downward to detach the 2 hooks and remove it.

  14. REMOVE FRONT SEAT LEG COVER LH

    Click here

  15. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH

    Click here

  16. REMOVE SEAT CUSHION COVER WITH PAD


    1. w/ Seat Heater System:


      1. A000QZNE01
        Text in Illustration
        *1 Connector Lock

        Disconnect the 2 connectors.

      2. Remove the connector lock from the seat heater control sub-assembly LH connector and disconnect the connector.

    2. Using a clip remover, remove the 4 clips.

      A000PKM
    3. A000OEY

      for Front Passenger Side:

      Disconnect the connector.

    4. Detach the hooks and remove the seat cushion cover with pad.

  17. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A000RKDE01
      Text in Illustration
      *1 Strap

      Remove the hog rings and disconnect the 3 straps from the separate type front seat cushion pad.

    2. A000T57

      Remove the hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.

  18. REMOVE SEAT CUSHION SPRING DAMPER

    Click here

  19. REMOVE SEATBACK COVER WITH PAD

    A000NMF

    1. Detach the hooks.

    2. A000RWJ

      Detach the 4 claws and remove the 2 front seat headrest supports.

    3. A000P2RE01

      Detach the wire harness clamp.

    4. Remove the 2 nuts and detach the 2 seatback cover brackets.

      Text in Illustration
      *1 Seatback Cover Bracket

    5. Remove the seatback cover with pad.

  20. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. A000RSC

      Pass the 2 seatback cover brackets through the 2 holes of the separate type front seatback pad.

    2. A000OI5

      Remove the hog rings and separate type front seatback cover from the separate type front seatback pad.

  21. REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY

    Click here

  22. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

    A000R1J

    1. Disconnect the connector.

    2. Detach the 2 claws and disconnect the rear air duct LH from the lumbar support adjuster assembly LH.

    3. Remove the 2 screws.

    4. Detach the hook and remove the seatback climate control blower LH together with the rear air duct LH.

  23. REMOVE REAR AIR DUCT LH (w/ Climate Control Seat System)

    Click here

  24. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Click here

  25. REMOVE FRONT SEATBACK INSIDE SPRING SET PLATE LH

    A000RYI

    1. Remove the front seatback inside spring set plate LH from the front seat bracket LH.

  26. REMOVE FRONT SEAT BRACKET LH

    A000QGC

    1. Remove the nut and front seat bracket LH.

  27. REMOVE FRONT SEATBACK INSIDE SPRING SET PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE FRONT SEAT BRACKET RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  30. REMOVE POWER SEAT MOTOR ASSEMBLY

    Click here

  31. REMOVE RECLINING ADJUSTER INSIDE COVER

    Click here

  32. REMOVE FRONT NO. 1 SEATBACK WIRE SET BRACKET

    A000OS4

    1. Remove the nut and front No. 1 seatback wire set bracket.

  33. REMOVE FRONT NO. 2 SEATBACK WIRE SET BRACKET

    A000SOC

    1. Remove the nut and front No. 2 seatback wire set bracket.

  34. REMOVE RECLINING ADJUSTER INSIDE COVER LH

    Click here

  35. REMOVE RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

    Click here

  37. REMOVE SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

    Click here

  38. REMOVE SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)

    Click here

  39. REMOVE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    A000OVBE03
    Text in Illustration
    *1 Wire Harness Clamp
    *2 Hook A
    *3 Hook B

    1. Detach the 3 wire harness clamps.

    2. Detach the 4 hooks A.

    3. Detach the 4 hooks B and remove the separate type front seat cushion spring assembly.

  40. REMOVE FRONT SEAT WIRE

    A000SGE

    1. Detach the 4 wire harness clamps.

    2. A000NYO

      Disconnect the 3 connectors.

    3. Detach the 9 wire harness clamps and remove the front seat wire.

  41. REMOVE SEATBACK FELT

    A000OAJ

    1. Remove the seatback felt.

  42. REMOVE FRONT SEATBACK FRAME SUB-ASSEMBLY LH

    Click here