FRONT SEAT ASSEMBLY(for Standard Seat Type) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note


    • After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

    • If the side airbag has deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

  2. REMOVE LUGGAGE COMPARTMENT FLOOR MAT

    Click here

  3. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  4. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. Remove the front seat headrest assembly.

  5. REMOVE SEAT BELT ANCHOR COVER CAP LH

    Click here

  6. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

  7. REMOVE FRONT SEAT OUTER TRACK BRACKET COVER LH

    Click here

  8. REMOVE FRONT SEAT INNER TRACK BRACKET COVER LH

    Click here

  9. REMOVE INNER SEAT TRACK BRACKET COVER LH

    Click here

  10. REMOVE OUTER SEAT TRACK BRACKET COVER LH

    Click here

  11. DISABLE AUTOAWAY/RETURN FUNCTION (w/ Memory)


    1. Disable the autoaway/return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the autoaway/return function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the autoaway/return function to be disabled when the power switch is turned off.

    2. Turn the power switch on (IG). Operate the tilt and telescopic switch to fully retract and tilt up the steering column assembly.

    3. Turn the power switch off.

  12. REMOVE FRONT SEAT ASSEMBLY


    1. A000Q7A

      Remove the 2 bolts.

    2. Operate the power seat slide switch and move the front seat assembly to the rearmost position.

    3. A000RC5

      Remove the 2 bolts.

    4. Operate the power seat slide switch and move the front seat assembly to the center position.

    5. Operate the power seat reclining switch and move the seatback to the upright position.

    6. Operate the power seat front vertical switch and rear lifter switch, and move the seat cushion to the uppermost position.

    7. Disconnect the cable from the auxiliary battery negative (-) terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    8. Tilt the front seat assembly to the rear of the vehicle.

      Note

      Be careful not to damage the front seat assembly and vehicle interior.

    9. A000SBRE01
      Text in Illustration
      *1 Protective Tape
      *2 Connector Lock Lever
      *3 Connector Lock
      *a Unlock Position

      Disconnect the connectors.


      1. Disconnect the connector.

      2. Push the connector lock to slide the airbag connector and disconnect it.

        Note

        When handling the airbag connector, take care not to damage the airbag wire harness or connector.

      3. Using a screwdriver, move the connector lock lever to the unlock position as shown in the illustration and disconnect the connector.

        Tech Tips

        Tape the screwdriver tip before use.

    10. Detach the wire harness clamp.

    11. Remove the front seat assembly from the vehicle.

      Note


      • 2 or more people are required when carrying the front seat assembly out of the vehicle.

      • Be careful not to damage the vehicle body.

      Tech Tips

      When removing the front seat assembly from the vehicle, pass it through under the steering wheel.