ENGINE IMMOBILISER SYSTEM, Diagnostic DTC:B279A-186

DTC Code DTC Name
B279A-186 Engine Immobiliser System Communication Line High Fixation

DESCRIPTION

When the communication line (IMI - EFIO) between the power management control ECU and ID code box (immobiliser code ECU) is stuck high, the power management control ECU stores this DTC.

DTC Code DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A-186 The communication line (IMI - EFIO) between the power management control ECU and ID code box (immobiliser code ECU) is stuck high (1 trip detection logic*).

  • Wire harness or connector (disconnection or break in wire harness is main cause)

  • ID code box (immobiliser code ECU)

  • Power management control ECU

 Turn the power switch on (IG) and wait 6 seconds.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Hybrid system cannot be started Hybrid system cannot be started
Related Data List and Active Test
DTC Code Data List and Active Test
B279A-186 -

WIRING DIAGRAM

A000RQDE02
*a ID Code Box (Immobiliser Code ECU)
*b Power Management Control ECU

CAUTION / NOTICE / HINT

Note


  • When replacing the ID code box (immobiliser code ECU), refer to the Service Bulletin.

  • After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again.

Tech Tips

When DTC B279A-186 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  2. CHECK FOR DTC


    1. Turn the power switch on (IG) and wait 10 seconds.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B279A-186 is output A
      DTC B279A-186 and other DTCs are output B

      Tech Tips

      If DTCs other than DTC B279A-186 are output, troubleshoot those DTCs first.


    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  3. CHECK CONNECTION OF CONNECTOR


    1. Turn the power switch off.

    2. Check that the connectors are properly connected to the power management control ECU and ID code box (immobiliser code ECU).

      OK
      Connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  4. CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - POWER MANAGEMENT CONTROL ECU)


    1. Disconnect the N73 ID code box (immobiliser code ECU) connector.

    2. Disconnect the N92 power management control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N73-4 (EFIO) - N92-29 (IMI) Always Below 1 Ω
      N92-29 (IMI) - Body ground Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N92-29 (IMI) - Body ground Always Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


    1. Replace the ID code box (immobiliser code ECU) with a new one.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  6. REGISTER RECOGNITION CODES


    1. Register the recognition codes in the ECUs.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  7. REGISTER ECU COMMUNICATION ID


    1. Register the ECU communication ID.

      Tech Tips

      Refer to the Service Bulletin.


    NEXT

  8. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  9. CHECK FOR DTC


    1. Check for DTCs Click here.

      Tech Tips

      Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

      OK
      DTC B279A-186 is not output.

    OK

    END (ID CODE BOX [IMMOBILISER CODE ECU] WAS DEFECTIVE)

    NG

    REPLACE POWER MANAGEMENT CONTROL ECU Click here