ENGINE IMMOBILISER SYSTEM HOW TO PROCEED WITH TROUBLESHOOTING

DTC Code DTC Name
HOW TO PROCEED WITH TROUBLESHOOTING

CAUTION / NOTICE / HINT

Tech Tips


  • Use this procedure to troubleshoot the engine immobiliser system.

  • *: Use the GTS.

PROCEDURE


  1. VEHICLE BROUGHT TO WORKSHOP

    Result
    Proceed to
    NEXT

    NEXT

  2. INSPECT AUXILIARY BATTERY VOLTAGE


    1. Measure the auxiliary battery voltage.

      Standard Voltage
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.

      Tech Tips

      A simple method to determine whether the auxiliary battery is discharged is to operate the horn.

      Result
      Proceed to
      NEXT

    NEXT

  3. TURN POWER SWITCH ON (IG)

    Tech Tips

    If the power switch cannot be turned on (IG), communication with the GTS can be confirmed by connecting the GTS to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and vehicle begins.

    Result
    Proceed to
    NEXT

    NEXT

  4. CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*


    1. Use the GTS to check if the CAN communication system is functioning normally.

      for LHD: Click here

      for RHD: Click here

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  5. CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*


    1. Use the GTS to check if the LIN communication system is functioning normally.

      Click here

      Result
      Result Proceed to
      LIN DTC is not output A
      LIN DTC is output B

    B

    GO TO LIN COMMUNICATION SYSTEM Click here

    A

  6. CHECK FOR DTC*


    1. Check for DTCs and make a note of any codes that are output.

      Click here

    2. Based on the DTCs output above, proceed to each diagnostic procedure.

      Result
      Result Proceed to
      DTC is not output A
      Hybrid system (for 2GR-FXE) DTC is output B
      Hybrid system (for 2AR-FSE) DTC is output C
      Steering lock system DTC is output D
      Engine immobiliser system DTC is output E

    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    C

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    D

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    E

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  7. PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table.

      Click here

      Result
      Result Proceed to
      Fault is not listed in problem symptoms table A
      Fault is listed in problem symptoms table B

    B

    ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

    A

  8. OVERALL ANALYSIS AND TROUBLESHOOTING*


    1. Data List / Active Test

      Click here

    2. Terminals of ECU

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  9. REPAIR OR REPLACE

    Result
    Proceed to
    NEXT

    NEXT

  10. CHECK FOR DTC*


    1. Clear the DTCs.

      Click here

    2. Check for DTCs.

      Click here

      Tech Tips

      Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.

      Click here

      Result
      Result Proceed to
      DTC is not output A
      Engine immobiliser system DTC is output B

    A

    END

    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here