FRONT DOOR LOCK INSPECTION

PROCEDURE

1. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

   

   Text in Illustration

   *a	Lock	*b	Unlock
   *c	Component without harness connected (Front Door Lock Assembly LH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the motor connector and check the operation of the front door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock

         
         

         • If the result is not as specified, replace the front door lock assembly LH.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 8 (LSSR) - 7 (E) Lock 10 kΩ or higher 8 (LSSR) - 7 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly LH.

   3. for LHD:

      

      Text in Illustration

      *a	Unlock	*b	Off
      *c	Lock	*d	Component without harness connected (Front Door Lock Assembly LH)

      
      

      1. Check the door lock and unlock switch.

         
         

         1. Measure the resistance according to the value(s) in the table below.

            Standard Resistance
            Tester Connection Condition Specified Condition 9 (L) - 7 (E) Lock Below 1 Ω 9 (L) - 7 (E) 10 (UL) - 7 (E) OFF 10 kΩ or higher 10 (UL) - 7 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly LH.

2. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

   

   Text in Illustration

   *a	Lock	*b	Unlock
   *c	Component without harness connected (Front Door Lock Assembly LH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL) Lock Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L) Unlock Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL) Set Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL) Unset

         
         

         • If the result is not as specified, replace the front door lock assembly LH.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 8 (LSSR) - 7 (E) Lock 10 kΩ or higher 8 (LSSR) - 7 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly LH.

   3. for LHD:

      

      Text in Illustration

      *a	Unlock	*b	Off
      *c	Lock	*d	Component without harness connected (Front Door Lock Assembly LH)

      
      

      1. Check the door lock and unlock switch.

         
         

         1. Measure the resistance according to the value(s) in the table below.

            Standard Resistance
            Tester Connection Condition Specified Condition 9 (L) - 7 (E) Lock Below 1 Ω 9 (L) - 7 (E) 10 (UL) - 7 (E) OFF 10 kΩ or higher 10 (UL) - 7 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly LH.

3. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

   

   Text in Illustration

   *a	Unlock	*b	Lock
   *c	Component without harness connected (Front Door Lock Assembly RH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock

         
         

         • If the result is not as specified, replace the front door lock assembly RH.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Lock 10 kΩ or higher 7 (LSSR) - 8 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly RH.

   3. for RHD:

      

      Text in Illustration

      *a	Unlock	*b	Off
      *c	Lock	*d	Component without harness connected (Front Door Lock Assembly RH)

      
      

      1. Check the door lock and unlock switch.

         
         

         1. Measure the resistance according to the value(s) in the table below.

            Standard Resistance
            Tester Connection Condition Specified Condition 6 (L) - 8 (E) Lock Below 1 Ω 6 (L) - 8 (E) 5 (UL) - 8 (E) OFF 10 kΩ or higher 5 (UL) - 8 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly RH.

4. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

   

   Text in Illustration

   *a	Unlock	*b	Lock
   *c	Component without harness connected (Front Door Lock Assembly RH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L) Unlock Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL) Set Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL) Unset

         
         

         • If the result is not as specified, replace the front door lock assembly RH.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 7 (LSSR) - 8 (E) Lock 10 kΩ or higher 7 (LSSR) - 8 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly RH.

   3. for RHD:

      

      Text in Illustration

      *a	Unlock	*b	Off
      *c	Lock	*d	Component without harness connected (Front Door Lock Assembly RH)

      
      

      1. Check the door lock and unlock switch.

         
         

         1. Measure the resistance according to the value(s) in the table below.

            Standard Resistance
            Tester Connection Condition Specified Condition 6 (L) - 8 (E) Lock Below 1 Ω 6 (L) - 8 (E) 5 (UL) - 8 (E) OFF 10 kΩ or higher 5 (UL) - 8 (E) Unlock Below 1 Ω

         
         

         • If the result is not as specified, replace the front door lock assembly RH.