CAN COMMUNICATION SYSTEM(for LHD) Front Camera Module Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode

Either Condition is met:


  • "Front Camera Module" is indicated on the "Bus Check" screen Click here

  • Communication system DTCs (DTCs that start with U) that are output correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table" Click here


  • Forward recognition camera CAN branch wire or connector

  • Power source circuit of forward recognition camera

  • Forward recognition camera ground circuit

  • Forward recognition camera

WIRING DIAGRAM

B002BPME41
*a No. 9 CAN Junction Connector
*b from LH-IG1 RLY1 Relay
*c Forward Recognition Camera

CAUTION / NOTICE / HINT

Note


  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output Click here.

  • Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: The vehicle has been driven for approximately 7 seconds or more at a speed of 1 km/h (1 mph) or more and with the IG voltage at 10 V or higher.

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed Click here.

Tech Tips


  • Operating the power switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE


  1. CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA CAN BRANCH WIRE)


    1. B002C4ME01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Forward Recognition Camera)

      Disconnect the cable from the negative (-) auxiliary battery terminal.

    2. Disconnect the forward recognition camera connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Y17-5 (CA1P) - Y17-11 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FORWARD RECOGNITION CAMERA (CA1P, CA1N)

    OK

  2. CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA - BATTERY AND BODY GROUND)


    1. B002BOWE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Forward Recognition Camera)

      Connect the cable to the negative (-) auxiliary battery terminal.

      Note

      When connecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      Y17-7 (IGB) - Body ground Power switch on (IG) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Y17-10 (GND) - Body ground Always Below 1 Ω

    OK

    REPLACE FORWARD RECOGNITION CAMERA Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR