FREEZE FRAME DATA
Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.
CHECK FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the blind spot monitor system on.
Turn the GTS on.
Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.
According to the display on the GTS, display the Freeze Frame Data for the selected DTC.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Main Switch | Blind spot monitor main switch (steering pad switch assembly) / OFF or ON | ON: Blind spot monitor main switch (steering pad switch assembly) on OFF: Blind spot monitor main switch (steering pad switch assembly) off |
- |
| Warning Indicator Turning on (Master) | State of the outer rear view mirror indicator RH turning on / OFF or ON | OFF: Any state except "ON" state
|
- |
| Warning Indicator Flashing (Master) | State of the outer rear view mirror indicator RH flashing / OFF or ON | OFF: Any state except "ON" state ON: Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on |
- |
| Warning Indicator Input Circuit Voltage | The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V | Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V |
- |
| Warning Indicator Input Circuit Current | The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA | Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA |
- |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off |
- |
| Reverse | State of the shift position R signal / OFF or ON | ON: Shift lever in R OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor / Min.: -3072°, Max.: 3070.5° | Left turn: Increases Right turn: Decreases |
- |
| VGRS Relative Angle | VGRS relative angle / -8.192 to 8.191 rad | -8.192 to 8.191 rad | - |
| Power Supply Voltage | Power supply voltage / Min.: 0 V, Max.: 49.951 V | 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state / Dim OFF or Dim ON | Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed |
- |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Number of DTC | Number of DTC / Min.: 0, Max.: 255 | When system is normal: 0 When a malfunction is detected: More than 0 |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Warning Indicator Turning on (Slave) | State of the outer rear view mirror indicator LH turning on / OFF or ON | OFF: Any state except "ON" state
|
- |
| Warning Indicator Flashing (Slave) | State of the outer rear view mirror indicator LH flashing / OFF or ON | OFF: Any state except "ON" state ON: Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on |
- |
| Buzzer Sound Status | State of the rear cross traffic alert buzzer (blind spot monitor buzzer) / OFF or ON | OFF: Buzzer not sounding ON: Buzzer sounding |
w/ RCTA |
| Warning Indicator Input Circuit Voltage | The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V | Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V |
- |
| Warning Indicator Input Circuit Current | The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA | Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA |
- |
| Buzzer Input Circuit Voltage | Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V | Buzzer not sounding: 11 to 14 V Buzzer sounding: Alternating between 0 to 14 V |
w/ RCTA |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off |
- |
| Reverse | State of the shift position R signal / OFF or ON | ON: Shift lever in R OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor / Min.: -3072°, Max.: 3070.5° | Left turn: Increases Right turn: Decreases |
- |
| VGRS Relative Angle | VGRS relative angle / -8.192 to 8.191 rad | -8.192 to 8.191 rad | - |
| Power Supply Voltage | Power supply voltage / Min.: 0 V, Max.: 49.951 V | Always: 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state / Dim OFF or Dim ON | Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed |
- |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Number of DTC | Number of DTC / Min.: 0, Max.: 255 | When system is normal: 0 When a malfunction is detected: More than 0 |
- |
CLEAR FREEZE FRAME DATA
Note
Clearing the DTCs will also clear the Freeze Frame Data.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the blind spot monitor system on.
Turn the GTS on.
Clear the DTCs and Freeze Frame Data.