REAR DOOR WINDOW FRAME MOULDING REMOVAL

CAUTION / NOTICE / HINT

PROCEDURE

1. PRECAUTION

   Note

   After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

2. REMOVE LUGGAGE COMPARTMENT FLOOR MAT

   Click here

3. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

   Click here

4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

   Note

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

   Click here

6. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

   Click here

7. REMOVE REAR DOOR HOLE COVER

   Click here

8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

   Click here

9. REMOVE REAR DOOR NO. 1 STIFFENER CUSHION

   Click here

10. REMOVE REAR DOOR TRIM COVER LH

    Click here

11. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

    Click here

12. REMOVE REAR SIDE CURTAIN ASSEMBLY LH (w/ Rear Sunshade)

    Click here

13. REMOVE REAR DOOR FRAME GARNISH LH

    Click here

14. REMOVE REAR DOOR ARMREST SET BRACKET LH

    Click here

15. REMOVE REAR NO. 2 SPEAKER ASSEMBLY

    Click here

16. REMOVE REAR DOOR SERVICE HOLE COVER LH

    Click here

17. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

    Click here

18. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

    Click here

19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

20. REMOVE REAR DOOR GLASS RUN LH

    Click here

21. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

22. REMOVE REAR DOOR WEATHERSTRIP LH

    
    

    1. 

       Remove the upper part of the rear door weatherstrip so that the moulding can be removed.

23. REMOVE REAR DOOR FRONT BELT MOULDING END COVER LH

    Tech Tips

    When removing the rear door front belt moulding end cover, heat the rear door panel and rear door front belt moulding end cover using a heat light.

    Standard
    Item Temperature Rear Door Panel 40 to 60°C (104 to 140°F) Rear Door Front Belt Moulding End Cover 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear door panel or rear door front belt moulding end cover excessively.

    
    
    1. 

       Text in Illustration

       *1	Protective Tape
       *2	Double-sided Tape

       Put protective tape around the rear door front belt moulding end cover.

    2. Using a moulding remover, detach the 2 clips.

    3. Detach the double-sided tape to remove the rear door front belt moulding end cover.

24. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

    Tech Tips

    When removing the rear door front window frame moulding, heat the rear door panel and rear door front window frame moulding using a heat light.

    Standard
    Item Temperature Rear Door Panel 40 to 60°C (104 to 140°F) Rear Door Front Window Frame Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear door panel or rear door front window frame moulding excessively.

    
    
    1. 

       Text in Illustration

       *1	Protective Tape
       *2	Double-sided Tape
       *3	Butyl Tape

       Put protective tape around the rear door front window frame moulding.

    2. Using a moulding remover, detach the clip.

    3. Detach the double-sided tape and butyl tape, and then detach the guide and remove the rear door front window frame moulding.

25. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH

    
    

    1. Put a 4 mm (0.157 in.) drill bit into a drill.

    2. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

       Tech Tips

       Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against the 8 rivets and drill off the flanges of the 8 rivets.

       CAUTION:

       Be careful of the drilled rivet as it may become hot.

       Note

       
       

       • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

       • Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

    4. Detach the 2 clips and remove the rear door window frame moulding.

    5. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.

       

       Standard
       Area Specified Condition A 5 mm (0.197 in.)