FRONT CAMERA REMOVAL

CAUTION / NOTICE / HINT

Note


  • When replacing the forward recognition camera, replace it with a new one.

  • Do not touch the camera lens or the front windshield glass in front of the camera.

  • If the forward recognition camera has been struck or dropped, replace it with a new one.

  • When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Lexus genuine part. If a non-Lexus genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket, or the road sign assist system, LKA/LDA system, forward recognition camera system, dynamic radar cruise control system, pre-crash safety system. automatic high beam system or adaptive high beam system may not operate properly due to a difference in the transmissivity of the windshield glass or the shape of the black ceramic border.

PROCEDURE


  1. REMOVE NO. 2 FORWARD RECOGNITION COVER


    1. B002BX4C02
      B002B6O Remove in this Direction (1)
      B002BBR Remove in this Direction (2)

      Detach the 2 claws and 2 guides and remove the No. 2 forward recognition cover as shown in the illustration.

      Note

      If these claws are detached separately, they may break. Detach the claws simultaneously.

  2. REMOVE NO. 1 FORWARD RECOGNITION COVER


    1. B002B6EC02
      B002B6O Remove in this Direction

      Detach the 2 clips and 2 guides and remove the No. 1 forward recognition cover as shown in the illustration.

      Note

      Push the cover while keeping it parallel with the surface of the glass so as not to damage the clips and guides.

  3. REMOVE FORWARD RECOGNITION LATCH


    1. B002C26C02
      B002B6O Remove in this Direction (1)
      B002BBR Remove in this Direction (2)

      w/o Camera Heater:


      1. Detach the 2 claws and 4 guides and remove the forward recognition latch as shown in the illustration.

    2. B002BALC02
      B002B6O Remove in this Direction (1)
      B002BBR Remove in this Direction (2)

      w/ Camera Heater:


      1. Detach the 2 claws and 4 guides and remove the forward recognition latch as shown in the illustration.

  4. REMOVE FORWARD RECOGNITION CAMERA


    1. B002BAGC02
      B002B6O Connector
      B002BBR Remove in this Direction

      w/o Camera Heater:

      Note


      • Do not pull the harness forcibly when disconnecting the connector.

      • If the forward recognition camera bracket is deformed or damaged, replace it together with the windshield glass.

      • If the forward recognition camera has been struck or dropped, replace it with a new one.

      • Do not apply excessive force.


      1. Disconnect the connector.

      2. Detach the 4 guides and remove the forward recognition camera as shown in the illustration.

    2. B002B73C03
      B002B6O Connector
      B002BBR Remove in this Direction

      w/ Camera Heater:

      Note


      • Do not pull the harness forcibly when disconnecting the connector.

      • If the forward recognition camera bracket is deformed or damaged, replace it together with the windshield glass.

      • If the forward recognition camera has been struck or dropped, replace it with a new one.

      • Do not apply excessive force.


      1. Disconnect the connector.

      2. Detach the 4 guides and remove the forward recognition camera as shown in the illustration.

  5. REMOVE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

    Note

    During work, do not touch the shaded area on the forward recognition with heater hood sub-assembly shown in the illustration.

    B002BGL

    1. B002B6D

      Disconnect the connector.

      Note

      Do not pull the harness forcibly when disconnecting the connector.

    2. B002BSP

      Detach the connector clamp.

    3. B002C1Y

      Detach the guide and remove the wire harness.

    4. B002C3SC02
      B002B6O Remove in this Direction (1)
      B002BBR Remove in this Direction (2)
      B002BQR Heater Area

      Detach the claw in the direction indicated by the arrow (1) in the illustration.

      Note

      Do not press the heater area.

    5. Detach the guide in the direction indicated by the arrow (2) in the illustration to remove the forward recognition with heater hood sub-assembly.