ENGINE UNIT INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

Perform "Inspection After Repair" after replacing the engine assembly.


PROCEDURE


  1. INSTALL WATER OUTLET SUB-ASSEMBLY

    Click here

  2. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

    Click here

  3. INSTALL FUEL INJECTOR SEAL

    Click here

  4. INSTALL FUEL INJECTOR SET

    Click here

  5. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

    Click here

  6. INSTALL FUEL INJECTOR ASSEMBLY

    Click here

  7. INSTALL FUEL DELIVERY PIPE

    Click here

  8. SET FUEL PUMP WITH SEAL SUB-ASSEMBLY

    Click here

  9. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

    Click here

  10. INSTALL FUEL PUMP WITH SEAL SUB-ASSEMBLY

    Click here

  11. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

    Click here

  12. INSTALL NO. 1 FUEL PIPE

    Click here

  13. INSTALL WATER INLET HOUSING

    Note

    If a stud bolt is deformed or its threads are damaged, replace it.


    1. A000P73E02
      Text in Illustration
      *a 16 mm (0.63 in.)
      *b 9 mm (0.354 in.)
      *c 27 mm (1.06 in.)

      Using an E6 "TORX" socket wrench, install the 8 stud bolts to the water inlet housing.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    2. Install a new gasket to the water inlet housing.

    3. Install the water inlet housing to the cylinder block sub-assembly with the 2 bolts and nut.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Note

      Keep the contact surfaces of the cylinder block sub-assembly and water inlet housing free of foreign matter.

      Tech Tips

      Align the straight pin of the cylinder block sub-assembly with the straight pin hole of the water inlet housing.

  14. INSTALL NO. 5 WATER BY-PASS PIPE


    1. Install a new gasket to the water inlet housing.

    2. Install the No. 5 water by-pass pipe to the water inlet housing with the bolt and 2 nuts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    3. Connect the No. 11 water by-pass hose to the water outlet sub-assembly and slide the clip to secure the hose.

  15. INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

    Click here

  16. INSTALL ENGINE WATER PUMP ASSEMBLY

    Click here

  17. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the 7 wire harness clamp brackets with the 9 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  18. INSTALL ENGINE COVER JOINT


    1. Install the 3 engine cover joints.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  19. INSTALL IGNITION COIL ASSEMBLY

    Click here

  20. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    1. Install the front No. 1 engine mounting bracket LH to the cylinder block sub-assembly with the 4 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  21. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    1. Install the front No. 1 engine mounting bracket RH to the cylinder block sub-assembly with the 4 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  22. INSTALL NO. 3 WATER BY-PASS PIPE


    1. Install the No. 3 water by-pass pipe to the cylinder block sub-assembly with the 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the No. 13 water by-pass hose to the water outlet sub-assembly and slide the clip to secure the hose.

  23. INSTALL NO. 2 WATER BY-PASS PIPE


    1. Install the No. 2 water by-pass pipe to the cylinder head sub-assembly with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  24. INSTALL EGR COOLER ASSEMBLY (w/ EGR System)

    Click here

  25. INSTALL EGR VALVE BRACKET (w/ EGR System)

    Click here

  26. INSTALL WATER BY-PASS PIPE (w/o EGR System)


    1. Install the water by-pass pipe to the cylinder head sub-assembly with the bolt and nut.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the No. 5 water by-pass hose and No. 6 water by-pass hose to the water by-pass pipe and slide the 2 clips to secure the hoses.

  27. INSTALL NO. 1 WATER BY-PASS PIPE


    1. Install a new gasket and the No. 1 water by-pass pipe with the bolt and 2 nuts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Connect the water by-pass hose to the No. 2 water by-pass pipe and slide the clip to secure the hose.

  28. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET


    1. Install the No. 1 compressor mounting bracket with the 5 bolts.

      Torque:
      25 N*m  { 250 kgf*cm, 18 ft.*lbf }