HYBRID CONTROL SYSTEM, Diagnostic DTC:P3000-603

DTC Code DTC Name
P3000-603 Battery Control System

DESCRIPTION

The power management control ECU monitors its internal operation and detects the following malfunction.

DTC No. INF Code DTC Detection Condition Trouble Area
P3000 603 The power management control ECU detects an HV battery cooling system error signal.

  • Power management control ECU

  • HV battery

CAUTION / NOTICE / HINT

CAUTION:

When disposing of an HV battery, make sure to return it through an authorized collection agent that is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      P3000-603 only is output. A
      DTCs other than P3000-603 are also output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  2. CLEAN BATTERY COOLING BLOWER FILTER


    1. Check the HV battery cooling system intake port for blockage.

      Tech Tips

      If anything is blocking the HV battery cooling system intake port, remove it.

      B002BDHE01
      Text in Illustration
      *a Intake Port - -

    2. Clean the battery cooling blower filter.

      Click here


    NEXT

  3. CHECK FREEZE FRAME DATA (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read the freeze frame data of DTC P3000-603.

      Note

      Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze flame data recorded before "0s" (when the DTC was stored).

      B002C0DE01
      Text in Illustration
      *a Freeze Frame Data Recorded
      *b DTC Stored
      *c Time
      Result
      Result Proceed to
      Other than below A
      The sum of the value of each hybrid battery block voltage ("Battery Block Vol-V01 to V20") is less than the value of "VL-Voltage before Boosting" by 10 V or more. B

    5. Turn the power switch off.


    B

    REPLACE BATTERY SMART UNIT Click here

    A

  4. CHECK FREEZE FRAME DATA (HYBRID CONTROL)


    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read the freeze frame data of DTC P3000-603.

      Note

      Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze flame data recorded at "0s" (when the DTC was stored).

      Result
      Result Proceed to
      Other than below A
      The value of any of "Temp of Batt TB1 to TB5" is 80°C (176°F) or higher. B

    5. Turn the power switch off.


    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    A

  5. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Data List / "Temp of Batt TB1 to TB5".

    4. According to the display on the GTS, read the Data List and check that the value of each "Temp of Batt TB1 to TB5" is 40°C (104°F) or less.

      Tech Tips

      If the value of any of "Temp of Batt TB1 to TB5" is more than 40°C (104°F), turn the power switch off and wait until the values to decrease to 40°C (104°F) or less before continuing this procedure.

    5. Enter the following menus: Powertrain / Hybrid Control / Data List / "Battery Block Vol - V01 to V20".

    6. According to the display on the GTS, read the Data List and check the value of each "Battery Block Vol-V01 to V20" with the power switch on (IG).

      B002BGHE02
      Text in Illustration
      *a Battery Block Vol -V01 *b Battery Block Vol -V02
      *c Battery Block Vol -V03 *d Battery Block Vol -V04
      *e Battery Block Vol -V05 *f Battery Block Vol -V06
      *g Battery Block Vol -V07 *h Battery Block Vol -V08
      *i Battery Block Vol -V09 *j Battery Block Vol -V10
      *k Battery Block Vol -V11 *l Battery Block Vol -V12
      *m Battery Block Vol -V13 *n Battery Block Vol -V14
      *o Battery Block Vol -V15 *p Battery Block Vol -V16
      *q Battery Block Vol -V17 *r Battery Block Vol -V18
      *s Battery Block Vol -V19 *t Battery Block Vol -V20
      Result
      Result Proceed to
      Other than below A
      The difference between the lowest and highest HV battery block voltage is 0.3 V or more. B

    7. Turn the power switch off.


    A

    COMPLETED

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

  6. REPLACE BATTERY SMART UNIT


    NEXT

    REPLACE HV BATTERY Click here

  7. REPLACE POWER MANAGEMENT CONTROL ECU


    1. Replace the power management control ECU Click here.


    NEXT

    REPLACE HV BATTERY Click here