HYBRID CONTROL SYSTEM, Diagnostic DTC:P3000-388

DTC Code DTC Name
P3000-388 Battery Control System

DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals received from the battery smart unit. This DTC is stored when the SOC (state of charge) of the HV battery starts to drop as a result of leaving the shift lever in N, running out of fuel, or a malfunction in the hybrid control system.

DTC No. INF Code DTC Detection Condition Trouble Area
P3000 388 Discharge inhibition control malfunction

  • Fuel level

  • HV battery

CAUTION / NOTICE / HINT

Tech Tips


  • If the vehicle is stopped or parked with the shift lever in N for a long time, DTC P3000-388 may be stored because the HV battery cannot be charged.

  • When the engine cannot be started, DTC P3000-388 may be stored because the HV battery cannot be charged.

  • Repeated engine start checks may cause the SOC to drop, resulting in DTC P3000-388 being stored. In this case, charge the HV battery using the THS charger.

  • Cranking the engine once causes the SOC to drop approximately 1%.

  • Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

  • Charging the HV battery using the THS charger takes approximately 10 minutes when the battery temperature is 25°C (77°F) or approximately 30 minutes when the battery temperature is 0°C (32°F).

  • The THS charger is a supplemental charging device that enables the engine to start (READY-on state).

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      P3000-388 or P3000-389 only is output. A
      Other DTCs are output in addition to P3000-388 or P3000-389. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  2. CHECK DTC OUTPUT (ENGINE AND ECT)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      NO DTCs are output. A
      DTCs are output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (SFI SYSTEM) Click here

    A

  3. CHECK AMOUNT OF FUEL


    1. Turn the power switch on (IG).

    2. Check the amount of fuel by referring to the fuel gauge in the meter.

      Result
      Result Proceed to
      Proper amount of fuel is in the tank. A
      There is no fuel in the tank. B

      Tech Tips

      Add fuel until the low fuel level warning light turns off.

    3. Turn the power switch off.


    B

    REFUEL VEHICLE

    A

  4. CHECK FREEZE FRAME DATA


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read the freeze frame data item "Shift Sensor Shift Pos" of DTC P3000-388.

      Note


      • When the freeze frame data "Shift Sensor Shift Pos" was N, DTC P3000-388 may be stored due to the vehicle was left with shift lever in N and the HV battery could not be charged.

      • If DTC "P3000-388" only is output, charge the HV battery without replacing the HV battery.

    5. Turn the power switch off.


    NEXT

  5. CHECK ENGINE START


    1. Turn the power switch on (READY).

    2. Check if the engine starts.

      Tech Tips


      • Depressing the accelerator pedal with the shift lever in P will cause the engine to start.

      • Turning the power switch on (READY) and off repeatedly while the SOC is low may cause the SOC to drop further, resulting in DTC P3000-389 being stored. Charge the HV battery using the THS charger as necessary.

      • Cranking the engine once causes the SOC to drop approximately 1%.

      • Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

      Result
      Result Proceed to
      The engine starts. A
      The engine does not start. B

    3. If the engine does not start, turn the power switch off.


    A

    LEAVE VEHICLE WITH SHIFT LEVER IN P, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

    B

  6. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read and record the DTCs and freeze frame data.

    5. Clear DTCs and freeze frame data.

    6. Turn the power switch off.


    NEXT

    CHARGE HV BATTERY (CHECK THAT ENGINE STARTS) Click here