REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT FLOOR MAT

    Click here

  3. REMOVE LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A000SEK

      Detach the 2 clips and 5 claws.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A000PL8

      Detach the 3 claws and remove the rear door inside handle bezel plug.

  7. REMOVE REAR DOOR HOLE COVER


    1. Remove the rear door hole cover.

  8. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A000Q9X

      Remove the 3 screws.

    2. Detach the 8 clips.

    3. A000N92E03

      Detach the reference boss in the direction indicated by the arrow in the illustration.

    4. Using a screwdriver, detach the 3 claws and remove the rear door trim board.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Reference Boss
      *2 Protective Tape

    5. Disconnect each connector.

    6. A000SRS

      Disconnect the rear door lock remote control cable and rear door inside locking cable.

  9. REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Sunshade)


    1. A000T44

      Remove the 7 screws and rear curtain.

  10. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

    Click here

  11. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. A000PTN

      Remove the 14 screws and rear door inside handle together with the rear door trim ornament and No. 1 interior illumination light.

    2. A000NQ9

      Remove the screw.

    3. Detach the claw and remove the rear door inside handle.

  12. REMOVE REAR DOOR TRIM ORNAMENT SUB-ASSEMBLY LH


    1. A000SG7

      Detach the 3 claws and remove the rear door trim ornament from the No. 1 interior illumination light.

  13. REMOVE NO. 2 COURTESY LIGHT ASSEMBLY

    Click here

  14. REMOVE REAR DOOR TRIM SEAL LH


    1. A000SYR

      Detach the 9 clips and remove the rear door trim seal.

  15. REMOVE REAR DOOR NO. 1 STIFFENER CUSHION


    1. A000QHK

      Remove the rear door No. 1 stiffener cushion.

  16. REMOVE REAR DOOR TRIM COVER LH


    1. A000OK6

      Detach the 6 clips and remove the rear door trim cover.

  17. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A000NIC

      Remove the rear door inner glass weatherstrip.

  18. REMOVE REAR SIDE CURTAIN ASSEMBLY LH (w/ Rear Sunshade)


    1. A000PN7

      Detach the 4 claws and 2 clips and remove the rear side curtain.

  19. REMOVE REAR DOOR FRAME GARNISH LH


    1. A000O55

      Detach the 2 clips and remove the rear door frame garnish.

  20. REMOVE REAR DOOR ARMREST SET BRACKET LH


    1. A000R0P

      Remove the 2 screws and rear door armrest set bracket.

  21. REMOVE REAR NO. 2 SPEAKER ASSEMBLY

    Click here

  22. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  23. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A000PSP

      Pull out the rear door lock remote control cable and rear door inside locking cable from the rear door service hole cover, and then remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the rear door panel.

  24. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Move the rear door window regulator so that the rear door glass channel can be seen.

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Remove the rear power window regulator switch assembly with rear door armrest base panel.

    6. A000T0A

      Partially remove the rear door glass run as shown in the illustration.

    7. A000PCN

      Remove the screw and 2 bolts.

    8. A000Q1X

      Remove the rear door rear lower window frame together with the rear door glass run as shown in the illustration.

    9. A000PS4

      Remove the rear door rear lower window frame from the rear door glass run.

  25. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A000RKE

      Remove the rear door quarter window glass.

  26. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH


    1. A000SOQ

      Remove the rear door quarter window weatherstrip from the rear door quarter window glass.

  27. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A000PD8

      Remove the rear door glass from the rear door window regulator as shown in the illustration.

      Note

      Do not damage the door glass.

  28. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH


    1. A000PICE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the rear door glass channel.

      Tech Tips

      Tape the screwdriver tip before use.

  29. REMOVE REAR DOOR GLASS CHANNEL FILLER


    1. A000OF4

      Remove the rear door glass channel filler.

  30. REMOVE REAR DOOR GLASS RUN LH


    1. Remove the front side of the rear door glass run.

  31. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

  32. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. Disconnect the connector.

    2. A000NYTE04
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.

    3. Remove the 3 bolts and rear door window regulator.

    4. Remove the temporary bolt from the rear door window regulator.

  33. REMOVE REAR DOOR LOCK ASSEMBLY LH

    Click here

  34. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A000R2EE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Detach the claw and open the cover.

    2. A000RVXE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Remove the rear door lock remote control cable.

  35. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A000OMBE02
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Detach the 3 claws and open the cover.

    2. A000NJGE01
      Text in Illustration
      *A w/o Double Locking System
      *B w/ Double Locking System

      Remove the rear door inside locking cable.

  36. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    1. A000PYQ

      Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle cover.

  37. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A000N95E02
      Text in Illustration
      *1 Temporary Bolt

      Using a screwdriver, detach the 2 claws of the connector cover in the direction indicated by the arrow in the illustration and disconnect the connector cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A000QBOE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw of the connector in the direction indicated by the arrow in the illustration and disconnect the connector.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A000NS5E02
      Text in Illustration
      *1 Holder

      Detach the holder in the direction indicated by the arrow in the illustration.

    4. A000NX4

      Remove the rear door outside handle by sliding and pulling it in the direction indicated by the arrow in the illustration.

  38. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. A000P4L

      Detach the 3 claws and remove the rear door front outside handle pad.

  39. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD LH


    1. A000PYZ

      Detach the 2 claws and remove the rear door rear outside handle pad.

  40. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A000NMV

      Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle frame.

    2. A000ND6

      Detach the clamp of the rear door wire.

  41. REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH


    1. A000OBJ

      Detach the 5 clips and remove the rear door No. 2 weatherstrip.

  42. REMOVE REAR DOOR NO. 3 WEATHERSTRIP LH


    1. A000O5H

      Remove the double-sided tape and rear door No. 3 weatherstrip.

  43. REMOVE REAR DOOR DUST PROOF SEAL


    1. A000SAG

      Detach the claw and remove the rear door dust proof seal.

  44. REMOVE REAR DOOR PANEL CUSHION


    1. A000REX

      Remove the rear door panel cushion.

  45. REMOVE REAR DOOR CHECK ASSEMBLY LH


    1. A000S0R

      Remove the bolt, 2 nuts and rear door check.

  46. REMOVE REAR DOOR WEATHERSTRIP LH


    1. A000NCZ

      Detach the 22 clips and remove the rear door weatherstrip.

  47. REMOVE REAR DOOR FRONT BELT MOULDING END COVER LH

    Click here

  48. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

    Click here

  49. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY LH

    Click here