POWER WINDOW CONTROL SYSTEM Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION


WIRING DIAGRAM

A000OA8E06

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.

  • If the power window regulator motor assembly has been replaced with a new one, initialize the power window control system Click here.

  • If the power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if the power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system Click here.

Tech Tips

Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

PROCEDURE


  1. READ VALUE USING GTS (D DOOR P/W SW)


    1. Use the Data List to check if the front power window regulator motor LH*1, RH*2 is functioning properly Click here.


      • *1: for LHD

      • *2: for RHD

      D-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Up SW Driver side power window manual up signal / ON or OFF

      ON: Front power window switch LH manual up operated

      OFF: Front power window switch LH not operated

      		 -
      D Door P/W Down SW Driver side power window manual down signal / ON or OFF

      ON: Front power window switch LH manual down operated

      OFF: Front power window switch LH not operated

      		 -
      OK
      On GTS screen, each item changes between ON and OFF according to above chart.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BATTERY AND BODY GROUND) Click here

    C

    CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - BATTERY AND BODY GROUND) Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (POWER WINDOW)


    1. Select the Active Test, use the GTS to generate a control command, and then check that the power window regulator motor operates Click here.

      D-Door Motor
      Tester Display Test Part Control Range Diagnostic Note
      Power Window Driver side power window OFF/UP/DOWN -
      OK
      The power window regulator motor operates normally.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    A

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    B

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    C

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

  3. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - BATTERY AND BODY GROUND)


    1. A000PSVE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Front Multiplex Network Door ECU LH)

      Disconnect the front multiplex network door ECU LH connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Q19-6 (BDR) - Q19-1 (GND) Always 11 to 14 V
      Q19-16 (BCUT) - Q19-1 (GND) Always 11 to 14 V
      Q19-3 (SIG) - Q19-1 (GND) Power switch on (IG) 11 to 14 V
      Standard Resistance
      Tester Connection Condition Specified Condition
      Q19-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU LH)


    1. Disconnect the Q25 multiplex network master switch assembly connector.

    2. Disconnect the Q19 front multiplex network door ECU LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q25-11 (B) - Q19-15 (CPBJ) Always Below 1 Ω
      Q25-12 (GND) - Q19-9 (SGND) Always Below 1 Ω
      Q25-11 (B) - Body ground Always 10 kΩ or higher
      Q25-12 (GND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - FRONT MULTIPLEX NETWORK DOOR ECU LH)


    1. Disconnect the Q17 front power window regulator motor assembly LH connector.

    2. Disconnect the Q19 front multiplex network door ECU LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q17-2 (B) - Q19-5 (BDRJ) Always Below 1 Ω
      Q17-1 (E) - Q19-2 (PWE) Always Below 1 Ω
      Q17-2 (B) - Body ground Always 10 kΩ or higher
      Q17-1 (E) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH


    1. Measure the voltage according to the value(s) in the table below.

      Tech Tips

      Check from the rear of the connector while it is connected to the front multiplex network door ECU LH.

      A000R9CE01
      Text in Illustration
      *a

      Component with harness connected

      (Front Multiplex Network Door ECU LH)

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      Q19-5 (BDRJ) - Body ground Always 11 to 14 V
      Q19-15 (CPBJ) - Body ground Always 11 to 14 V

    NG

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    OK

  7. INSPECT FRONT DOOR MULTIPLEX NETWORK DOOR ECU LH


    1. Remove the front multiplex network door ECU LH Click here.

      A000RR1E03
      *1 PWE

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (PWE) - 1 (GND) Always Below 1 Ω
      9 (SGND) - 1 (GND) Always Below 1 Ω

    NG

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the Q25 multiplex network master switch assembly connector.

    2. Disconnect the Q17 power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q25-20 (UP) - Q17-10 (UP1) Always Below 1 Ω
      Q25-15 (DOWN) - Q17-7 (DWN1) Always Below 1 Ω
      Q25-20 (UP) - Body ground Always 10 kΩ or higher
      Q25-15 (DOWN) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. Remove the front power window regulator motor LH Click here.

    2. Inspect the front power window regulator motor LH Click here.


    OK

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

  10. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - BATTERY AND BODY GROUND)


    1. A000P5AE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Front Multiplex Network Door ECU RH)

      Disconnect the front multiplex network door ECU RH connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Q4-6 (BDR) - Q4-1 (GND) Always 11 to 14 V
      Q4-16 (BCUT) - Q4-1 (GND) Always 11 to 14 V
      Q4-3 (SIG) - Q4-1 (GND) Power switch on (IG) 11 to 14 V
      Standard Resistance
      Tester Connection Condition Specified Condition
      Q4-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT MULTIPLEX NETWORK DOOR ECU RH)


    1. Disconnect the Q10 multiplex network master switch assembly connector.

    2. Disconnect the Q4 front multiplex network door ECU RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q10-11 (B) - Q4-15 (CPBJ) Always Below 1 Ω
      Q10-12 (GND) - Q4-9 (SGND) Always Below 1 Ω
      Q10-11 (B) - Body ground Always 10 kΩ or higher
      Q10-12 (GND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - FRONT MULTIPLEX NETWORK DOORECU RH)


    1. Disconnect the Q2 front power window regulator motor assembly RH connector.

    2. Disconnect the Q4 front multiplex network door ECU RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q2-2 (B) - Q4-5 (BDRJ) Always Below 1 Ω
      Q2-1 (E) - Q4-2 (PWE) Always Below 1 Ω
      Q2-2 (B) - Body ground Always 10 kΩ or higher
      Q2-1 (E) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH


    1. Measure the voltage according to the value(s) in the table below.

      Tech Tips

      Check from the rear of the connector while it is connected to the front multiplex network door ECU RH.

      A000OW9E01
      Text in Illustration
      *a

      Component with harness connected

      (Front Multiplex Network Door ECU RH)

      		 - -
      Standard Voltage
      Tester Connection Condition Specified Condition
      Q4-5 (BDRJ) - Body ground Always 11 to 14 V
      Q4-15 (CPBJ) - Body ground Always 11 to 14 V

    NG

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    OK

  14. INSPECT FRONT MULTIPLEX NETWORK DOOR ECU RH


    1. Remove the front multiplex network door ECU RH Click here.

      A000RR1E03
      *1 PWE

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (PWE) - 1 (GND) Always Below 1 Ω
      9 (SGND) - 1 (GND) Always Below 1 Ω

    NG

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH Click here

    OK

  15. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTORASSEMBLY RH)


    1. Disconnect the Q10 multiplex network master switch assembly connector.

    2. Disconnect the Q2 power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Q10-20 (UP) - Q2-10 (UP1) Always Below 1 Ω
      Q10-15 (DOWN) - Q2-7 (DWN1) Always Below 1 Ω
      Q10-20 (UP) - Body ground Always 10 kΩ or higher
      Q10-15 (DOWN) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    1. Remove the front power window regulator motor RH Click here.

    2. Inspect the front power window regulator motor RH Click here.


    OK

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here